Yes, but check if the required input voltage of the refrigerator is actually 110 to 120 volts and preferable use an exclusive circuit having a 15 amp breaker for residential of commercial use. In most cases, this is fine. However, if, on the off-chance, your refrigerator's installation manual or rating plate tells you that it needs its own 20 amp circuit, then a 20 amp receptacle must be used. Note: An outlet on a dedicated circuit MUST NOT be rated less than the over-protection device (fuse or circuit breaker) protecting that dedicated circuit. By the same token if you are using a 20 dedicated circuit then the wire rating has to match the amperage. #14 wire is rated at 15 amps, # 12 wire is rated at 20 amps. SAFETY ADVICE
Before you do any work yourself,
on household electricity supplies, equipment or appliances,
always turn off the power
at the breaker box/fuse panel BEFORE you attempt to do any work AND
always use an electrician's test meter having metal-tipped probes
(not a simple proximity voltage indicator)
to ensure the circuit is, in fact, de-energized.
IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOB
SAFELY AND COMPETENTLY
REFER THIS WORK TO QUALIFIED PROFESSIONALS.
ALWAYS CHECK WITH YOUR LOCAL WIRING SAFETY OFFICE BEFORE YOU ATTEMPT TO CHANGE ANYTHING
- BREAKER PANEL, BREAKERS, CABLES OR OUTLETS -
ON ANY ELECTRICAL CIRCUITS.
Yes, In fact it should be on a dedicated circuit so that other appliances etc cannot overload the circuit.
A refrigerator is one of the appliances that need to have a dedicated circuit in the CEC. As the two codes are similar in many respects I would imagine it is the same in the NEC.
By code you're supposed to have a dedicated 20 amp circuit. But if you have an existing 15 amp circuit it might be fine for now if your microwave is 1400 watts or less and there's nothing else drawing power from that circuit. But if your running it new definitely run a 20 amp circuit dedicated on 12 gauge wire. That will allow you to use any microwave you want now and in the future.
A plug and play 15v amp circuit is one that you can simply plug in. It has a three pronged plug so no special wiring is needed.
A dedicated outlet is a single circuit from a single or double pole breaker to a specific outlet or receptacle for a single specific device or appliance. An example of this would be a circuit for a refrigerator, microwave, dryer, range, etc..This is typically referred to as a "dedicated circuit". A dedicated circuit usually is supplying power to only one or perhaps two receptacles, such as a computer station. An example in your home under current code is your washing machine is required to be on a dedicated circuit. Dedicated receptacle circuits may be either 15 or 20 amp.A dedicated circuit is just what it sounds like. I'ts a circuit dedicated to one particular device. Most receptacle (you may call them outlet's) circuits will power several outlets. A dedicated circuit will power only one specific outlet or appliance. Some examples would be a refrigerator, a garbage disposal, or a microwave.
There isn't a formula, but the general rule is that you allow for 1 amp per outlet and you load the circuit to 80% of maximum. For a 15 Amp circuit you can have a maximum of 12 outlets.
7 on a 15 amp circuit and 9 on a 20 amp circuit.
For a standard size refrigerator, a dedicated 15 amp circuit is used.
A 15 amp dedicated circuit breaker should be used for the dishwasher. The disposal can be wired to the general kitchen 15 amp circuit.
By code you're supposed to have a dedicated 20 amp circuit. But if you have an existing 15 amp circuit it might be fine for now if your microwave is 1400 watts or less and there's nothing else drawing power from that circuit. But if your running it new definitely run a 20 amp circuit dedicated on 12 gauge wire. That will allow you to use any microwave you want now and in the future.
Not in the latest edition of the code book. It should be on a 15 amp dedicated circuit.
The electrical requirements for a Kenmore refrigerator when roughing a house typically include a dedicated 15-20 amp circuit with a standard three-pronged electrical outlet. It's important to have proper grounding and polarity for safety and performance. Always refer to the specific model's installation guide for detailed electrical requirements.
A plug and play 15v amp circuit is one that you can simply plug in. It has a three pronged plug so no special wiring is needed.
Yes, if the manufacturer installed a parallel blade 15 amp rating cap on the end of the cord then just plug it in. The circuit that you plug into should be a dedicated circuit (nothing else on the circuit) because the amperage will be 13 amps at 120 volts.
At 120 volts a 15 amp circuit wired with #14 wire used for a dedicated light circuit do not install any more than 1400 total watts in lighting. If used for an dedicated outlet circuit do not install more than 8 outlets.
It depends on what the amperage of the connected load is. If it above 10 amps on a 15 amp breaker then make is a dedicated circuit. If it is used for lamps in the center of a room, then the floor outlet can be incorporated into the regular lighting and receptacle circuit.
As of 2014 all refrigerators must be on a GFCI protected circuit and it must be readily accessible. If you wire the refrigerator on a 15 amp circuit using AWG #14 wire it must be on a dedicated GFCI protected circuit, no exceptions. As you will normally mount the outlet behind the refrigerator you would have to move the unit to reset the breaker if and when it tripped. I would wire the refrigerator on one of the 20 amp kitchen counter-top circuits that is GFCI protected. Now, my answer may be debatable but from how I read the NEC code you can wire it to one of the kitchen branch circuits as long as the refrigerator does not pull more than 16 amps. You might want to check with your local inspector to get his opinion as he is the one who will have the final say.
A #14 copper wire rated at 15 amps is the minimum size wire for a 15 amp receptacle.
According to the Canadian Electrical Code; no more than 12 items can be on any one circuit. If it is possible to calculate the load of each outlet, you may end up with a smaller number. Also certain items must have a dedicated circuit ie. refrigerator, microwave above a stove, etc.