0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Why would you have a capacitor in series with a ballast in a fluorescent light?
The purpose is twofold. First it is a transformer which steps up the voltage to an amount that will operate the lamp. Secondly it acts as a resistance for the lamp. Without it the flourescent lamp would keep increasing current flow until it would completely burn itself out.
How do you remove a non-integrated bi-pin double-turn compact fluorescent lamp?
Pull the light globe straight out of the fitting. No twisting.
Can one replace a tungsten bulb with a compact fluorescent bulb?
Yes, if it fits the socket and the light fitting, or lamp fixture, with its cover or shade. You will not be able to dim the compact fluorescent as you did the incandescent (unless you have a really fancy dimmer).
How do you install fluorescent tube light?
Depends on what kind of tube light. Some have 2 pins and those you stick in and turn 90 degrees. Some have slots or a single large pin where one end of the light is spring loaded. You push one end in the spring loaded end and then connect the other end. Others have a 2 pin connecting that just snaps in.
Was the fluorescent light a solution to a problem?
The florescent light solved the problem of producing more light without needing to rewire buildings. It was also a way of producing light for less cost.
How does a fluorescent light fitting operate?
mercury
Does a fluorescent light fitting with 4 x T8 2' 18W tubes and a 48W ballast use all 120W when running?
No, a fluorescent light fitting with a 4xT8 2' 18W tube and a 48W ballast does not use all the 120W when running.
Why would you have a capacitor in series with a ballast in a fluorescent light?
The purpose is twofold. First it is a transformer which steps up the voltage to an amount that will operate the lamp. Secondly it acts as a resistance for the lamp. Without it the flourescent lamp would keep increasing current flow until it would completely burn itself out.
The lagalities regarding modifying a fluorescent light batten holder for fitting a led light t8 tubeI will be bridging the ballast and removing the starterI am a competent person1?
No. You are not.
How do you remove a non-integrated bi-pin double-turn compact fluorescent lamp?
Pull the light globe straight out of the fitting. No twisting.
Can one replace a tungsten bulb with a compact fluorescent bulb?
Yes, if it fits the socket and the light fitting, or lamp fixture, with its cover or shade. You will not be able to dim the compact fluorescent as you did the incandescent (unless you have a really fancy dimmer).
Is there such a thing as light without heat?
The fluorescent lighting is considered cold, but it is not totally correct.
How is fluorescent different from natural light?
Well.. the difference is that fluorescent light isn't natural and natural light isn't fluorescent . its not rocket science (:
Does a ballast use electricity if no bulbs are present?
If you mean the ballast in a fluorescent light fitting where the ballast is wired in series with the tube, the answer is "No". Explanation: If no tube is in place, the light fitting's circuit is "open" so there is nothing to take any current from the "hot" supply wire and return it to the "neutral" wire.
Is there any electrical hazard when removing a fluorescent tube?
The electrical connections for a fluorescent tube are quite small and also inside the lamp holder at either end of the bulb (2 on each end).Since you won't be able to put your finger into these connections regardless of whether the lamp is in or not, there is no real electrical hazard when removing a fluorescent lamp while it is turned on. However it should be noted that this is only under normal operating conditions and if a fault is present there could be a chance of a hazard from any metal parts of the light fitting (not the tube).If the light fitting is turned off, there will be no voltage in the fitting and hence no electrical hazard anywhere on the fitting (again not accounting for faults). This is how I would recommend changing a tube (this is not always possible where the fitting is the only source of light).It should be noted that fluorescent tubes can heat up during operation and that dust may have settled on top the lamp, so appropriate safety equipment is recommended (gloves and goggles). You will also generally be working at height.Lastly fluorescent tubes are glass so take appropriate care when handling.If in doubt please contact an electrician.
Why does a plasma ball make fluorescent light bulbs light up?
Anything that excites the gas in a fluorescent will make it light. Static electricity from the carpet will cause compact fluorescent to light.
Why diamond glows in dark?
Some diamonds are fluorescent. This means that light enters the stone and the wave length is converted to a longer light wave. Not all diamonds are fluorescent. No diamond will 'glow in the dark' without first being exposed to a light source.
