0
Yes, but only on the joints that butt a wall or cabinet.
Joints where one piece of floor butts another must have the tongue and groove left on them.
Wiki User
∙ 15y ago
Wiki User
∙ 15y agoYou can use it for the cuts that butt up to a wall, but the ends that butt one another should have the tongue and groove on them.
Add your answer:
Earn +20 pts
What size miter saw do you need?
I like to use a 12 inch dewalt miter saw. But really it depends on what you will be trimming to figure out exactly what size you will need. Mike
Can ferrous materials be cut using a miter saw?
yes use carbide blade
What saws do you use to make a clock?
Depending on whether you are going to a make a clock from scratch or use pre-fabricated pieces, you might need to use a miter saw or a dremmel. A miter saw is used to cut larger pieces of wood into smaller ones, and a dremel is used for detail work.
What is Dewalt miter saw used for?
Miter saws are tools used to make crosscuts. A crosscut is a cut made perpendicular to the grain of the wood. Miter saws are still in use in some places, but power tools have mostly overtaken them in woodworking.
What is a good sealent for wooden flooring?
The best sealant to use for wooden flooring would be to use a water based floor sealant . The drying time for this product is around 2 to 3 hours , it dries clear and it doesnt emit any harsh fumes .
Can use rubbing alchochol on laminte flooring?
Either stone or wooden. Take a look at the infographic below.
Which kind of saw would you use to cut out a wooden puzzle?
I have done it on a scrollsaw.
Is slate flooring harder to install than other types of flooring?
Slate flooring is not harder to install than other types of flooring, it just takes a little more care. Before you install it, you have to lay it out in the pattern you like and then use a wet saw to cut the pieces.
How do you cut laminate flooring?
The best way to cut laminate flooring is with either a power mitre saw, or a table saw. Depending on which way you are cutting it. To cut the length, use a power mitre saw, with a 40 tooth+ blade, keeping the "good" or "top" side up. If it's a 3" plank, you can use a 7 1/4" saw, a 5" a 10" saw, and anything bigger you should use a 12" saw. It's dangerous to make a parial cut, then turn the piece around to finish the cut. To "rip" the plank (cut along the length of the plank to make it "skinnier") you'll need to use a table saw, with a guide, and of course the blade guard. THE USE OF POWER SAWS CAN BE EXTREMELY DANGEROUS, BE CAREFUL, READ THE INSTRUCTIONS, ALWAYS WEAR EYE PROTECTION, ALWAYS KEEP YOUR FINGERS AWAY FROM THE BLADE, AND DO NOT RUSH YOUR CUT. IF YOU ARE A NOVICE, NOT FAMILIAR WITH THESE TOOLS, I'D RECOMMEND HIRING A PROFESSIONAL LICENSED FLOORING CONTRACTOR. THE PRICE YOU'D PAY A PRO IS A LOT LESS THAN LOSING A FINGER, OR FINGERS, OR AN EYE, ETC.
How do you saw timber?
First, there are several types of saw that you can use to cut timber. There is the hand saw, tenon saw, and the miter saw. You must first know what type of saw you can use to easily saw a timber. The oak timber, for example, is a hardwood and would require lots of force to be able to saw it. But generally, knowledge and experience are both essential in order to do it right and safe. You must be able to hold the timber securely and use safety gear before cutting to avoid accidents.
Can you use a miter saw to cut slate tile?
Yes, with a stone cutting blade, but it would have to be a blade made to cut while dry and it would be a slow process with lots of dust.
How do you cut shims on a table saw?
Depending on how comfortable you are using a table saw, you can do it free hand or with the miter gauge. Use a 6 inch piece of 2x6 and run it through at an angle. Usually about 1/4 inch thick on the thick end.
