0
Can you use an rcl 3000 lamp with a dead battery by plugging it into the wall?
Zachyra35
No. The instruction manual for the RCL 3000 "Rechargable Remote Control Lantern" specifically states that the 120V House Current Adapter will not power the lantern and is only for charging the battery.
You can replace the battery though...
Brand = SkyTech
Model = SC 46
Volts = 6 DC
Ah = 4 (or 4.5)
ApexBattery.com has them as of 1/30/2011 @ $7.95 each.
Note: There are other tricks you can do to make the lantern work without a battery, but it requires knowing a little about electronics.
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
What is HIT lamp?
Tubular Meta Halide Lamp
What are the characteristics of a simple circuit?
A simple circuit consists of a source of electro motive force ( EMF or voltage V ) This could be a battery,dynamo or solar cell. The circuit should do something, like light a lamp. For the lamp to glow there must be a flow of electrons called an electric current measure in Amperes (I). For the current to flow the circuit must form a closed loop, like a daisy chain. A switch is a device that breaks this loop and controls the state of the circuit. Closed circuit, switch closed, = lamp on Open circuit, switch not closed = lamp off
What are the different types of lamp holders?
what is surface type lamp holder
How does changing voltage across a lamp affect the power consumption of the lamp?
because it does!
Which kind a light bulb uses the least amount of energy a fluorescent lamp a halogen lamp a incandescent lamp or a heating lamp?
Fluorescent lights use far less energy than any of the others listed.
What type of battery is used in a lamp?
None a lamp uses a lightbulb
What if my car won't turn on but the brake lamp turns on?
That would tell me that your battery is not dead because you do not need the car turned on for your brake lights to operate
The lamp recommended for testing the output of battery recharging devices for cordless appliances is the?
Radio pilot lamp
The lamp recommended for testing the output of a battery-recharging devices for cordless appliances is the?
Radio pilot lamp
Which lamp is used in spectrophotometer?
An infrared photodiode with a wavelength ranging from about 300-3000 nm
Are newborn Coyotes lighter than a battery lamp?
Wat
How do you replace left low beam headlight 2004 Accord?
1. Remove the battery and battery holder to gain access to the lamp. 2. Remove the electrical plug from the lamp. 3. Remove three Phillips screws that hold in the lamp. 4. Install replacement bulb. 5. Replace screws. 6. Reconnect electrical plug. 7. Replace battery holder and battery.
What happen to the bulb when the copper wire connect to the battery?
if the copper wire (s) were conneting the battery to the lamp removing one of the wires would break a circut and the lamp goes out.
What happens when you disconnect the wire from the battery?
Disconnecting a wire from a battery would break the circuit. If the battery was powering a bulb, the lamp would go out.
Why is battery dead in morning on vectra could it be alarm it is fine during day but overnight the battery dies?
Check the battery first. Sometimes when a battery is starting to go bad it will just refuse to hold a charge for any length of time. *A common cause of this on Vectras is the luggage compartment lamp staying on when boot/tailgate lid is closed.The bracket mounting the switch gets bent and causes the lamp to stay on,sometimes wires catch and shortout.You need to get in the boot and have it closed on you to check.
I have a hurricane lamp with a 6v 6 amp rechargeable battery that no longer holds a charge and wonder can I substitute a rechargeable 6v 12 amp battery?
Yes you can. The battery supplies only as much current (amps) as the lamp draws when connected to 6 volts. The "12 amp" battery won't supply any more current when the lamp is shining than the "6 amp" battery did, but it'll last twice as long between charges.
When a 12 V battery ie a battery of EMF 12 V is connected across a lamp with a resistance of 6.8 ohms the potential difference across the lamp is 10.2 V Find the current through the lamp?
The idea is to use Ohm's Law (V=IR). In this case, the relevant voltage is the 10.2 V across the lamp.
