Depends on the receiver. Some models have just a pass thru feature and connot decode the audio portion of the HDMI signal, and therefore will need a digital audio cable to get sound. Some receivers can decode the audio, so you will need to consult your manual to see what they say. If you need a audio cable it will tell you.
I plugged the HDMI cable into the HDTV and into the PS3. Then I went to the settings for both the HDTV and the PS3 slim and set them for HDMI and sync. When it works right putting a disc into the PS3 will turn on the HDTV and also switch the HDTV over to that HDMI input rather than a cable box or similar item even if it was on the cable box when you last used the HDTV.
You can connect your DISH receiver to your Bravia TV using one of 4 methods: Coax cable connected to your coax port (non HD receiver) RCA (composite cable) - yellow, white, and red tips Component cable/ audio cable - Green, blue, red, white, and red (white and red for audio), HD receiver or HDMI cable (HD receiver). The component and HDMI give the highest video and audio quality. To receive HD programming, you need an HD receiver and HD programming package.
High Speed HDMI Cable with Ethernet is the fastest at the moment (HDMI 1.4)
Because HDMI carries digital data, any cable will carry the data as well as any other. The digital interface means that the data is recovered by the receiver with no loss whatsoever. If a cable is so poor that it won't carry the data well enough for the receiver to recover it, there will be no picture at all. Any HDMI tested and approved cable will carry data flawlessly. All cables on sale should be made and tested to thos standards. Cheaper HDMI cables are likely to be light weight with lower quality connectors. They may eventually fail if they are being handled and unplugged continually but other than that, expensive cables have no benefit over the very cheapest of HDMI cable.
The optical output of the PS3 can be connected to older surround sound receivers. Newer receivers can be connected with the HDMI cable.
If your surround receiver has HDMI, connect an HDMI cable from the NeoTV to the receiver, and then HDMI out the receiver to the TV. If you don't have HDMI on your receiver, you can connect an optical cable from the NEOTV to the surround receiver.
There are essentially two ways to get surround sound out of the Xbox. Via HDMI or via optical (TOSLINK) out. If you have the component video cable, then the end that attaches to the Xbox has an optical out port. Simply attach this to the optical in on your home theatre receiver with an optical cable. If you want to use audio via HDMI, in order to get surround sound you'll have to have an HDMI receiver capable of receiving audio. In this case run the Xbox via HDMI to the receiver and then the receiver via HDMI to the TV. The HDMI will send both audio and video. If you have the official Xbox HDMI cable you can also connect the HDMI cable directly to the TV and use the optical out connector that it comes with instead.
To use an HDMI cable for your receiver, you need a VIP receiver.. Each of these receivers have an HDMI port you can use to connect to your TV. You also need HD programming to take full advantage of the HD receiver and HDMI cable.
You may not be able to get it to work through your receiver due to the HDMI HDCP copy protection feature. The Starchoice tuners have to be set up to allow the display on your brand of TV and Receiver. If your brand of receiver isn't supported as an HDCP-compliant device, then you won't see a picture. You'll have to connect directly to the TV and run a coaxial or optical digital cable to the receiver for the audio.
You can't. You will have to use a HD cable box with an HDMI output to connect this receiver.
You'll need a receiver with at least 2 HDMI inputs and 1 output, as well as an HD-capable cable box. Connect the XBOX and the cable box to the receiver with the HDMI cables, and then plug the HDMI output on the receiver to the TV.
Your TV will not have a optical cable input. The easiest way is to connect an HDMI cable from the Blu-Ray player to the TV. This cable will have both the video and audio together. If you do not have an HDMI input on your TV, use the component video output from the Blu-Ray player and the analog left and right audio to connect to the TV, or connect the optical digital output from the Blu-Ray player to a surround sound receiver for sound amplification.
I plugged the HDMI cable into the HDTV and into the PS3. Then I went to the settings for both the HDTV and the PS3 slim and set them for HDMI and sync. When it works right putting a disc into the PS3 will turn on the HDTV and also switch the HDTV over to that HDMI input rather than a cable box or similar item even if it was on the cable box when you last used the HDTV.
It will send audio back to the receiver to eliminate needing an additional HDMI cable.
Yes you can provided that you have a additional sound system like a stereo receiver for the sound, if you a cable box/satellite receiver of and HDTV Receiver with either a HDMI or DVI port, (you'll need a converter cable for HDMI)
There is no difference in the picture quality. You simply need to purchase the cable for the application that you have. If you have a normal Blu-Ray, HDTV and Cable or Satellite HD receiver, a HDMI 1.3 cable is the right type. For 3D televisions, purchase a 1.4 cable.
I don't think the HDMI signal can be split.