i changed the spark plugs on my Nissan altima 2003 3.5 engine. i removed the intake manifold but didn't remove the battery cable and now the car accelerates and decelerates on its own. What can I do to fix this?

yOU HAVE TO FIGURE OUT WHICH CABLE IS BROKEN (LEFT OR RIGHT) BY PULLING OFF THE BRAKE LEVER COVER (sorry about the caps lock)

The bar across the top of the lever is the cable connection keeper. High end is the broken cable.

You have to remove the rear tire and brake drum to change the broken cable. It is torqued to amazing tightness so I'd suggest a local garage for this if you are a novice. It has to go in from the wheel side, up the tube, out into the levelr area, turn up around the lever and into the keeper. It'll drive you nuts and get REALLY greasy.

Also a good time to go ahead and get the rear brakes serviced. Make sure they turn the drums smooth on a lathe and use new cotter pins on the big axle nut. If you do not see a silver cotter pin bent over the big nut make them change it.

The computer in the car will not hold memory, the windshield washer only work on one speed, bright light will not work, I have to put the radio code in every-time I start the car. 2001 Mitsubishi Galant.

181 hp

200

900

Hi,

I am currently undergoing that process right now on my 04 tibby. It's a helluva process. You can go to the Hyundai service web site and it'll show you how to change it. Step by excruciating step. It doesn't seem so hard but there are a lot of hard to reach places.

For the clutch you will have to click on the SHOP tab. Select your make and year and engine size and it'll pull up everything you need to know about your Hyundai, all schematics and everything.

www.hmaservice.com

Thanks

Sami

04 Tiburon 2.7 GT V6

Timing BELT on both the 2.0 liter 4 cylinder and the 2.7 liter V6

Well I have a 2005 and the cruise control is on the steering wheel push the button in (towards the center of the steering wheel) at the top of the top of the switch. then push the top side down to set the speed that you want it at. push the switch up or down to control the speed without the gas and brake. Hope that answers the question.

4x114.3

go to autozone and have them hook it up to there computer and if you've already fixed the problem they can reset it.

How many rpm should the engine turn at 80 Mph 2007 Hyundai tiburon

Yes you can as long as the rim diameter is the same. You left off the last number on your size. The sidewall will be taller on the 65 versus the 55 and this will affect the overall diameter of the tire so your speedometer may/will be off depending on the year of your car. The 65 will make less revolutions per mile than the 55.

this means that either your exhaust/gas value isn't working properly or a bad senor that can be replaced if your under warranty or can pay about 100.00. but unsure if Hyundai acts like Honda in a way that the check light is program to go off just as a check method for the car and as a reminder.....hope this helps

Don't believe last answer is correct, if you meant "O/D off" indicator light is on, then it means your overdrive is turned off, I have a 2001 Tiburon and there is a button located on the my shifter that allows you to turn the overdrive on and off.

• Front: 6-1/2"
• Rear: 6" x 9"
• Front door: 6-1/2"
• Rear side panel: 6" x 9"

The filter is in the fuel tank as part of the fuel pump assembly. To access, you'll need to remove the rear seat bottom and the access panel underneath the seat. Then you'll be able to remove the fuel pump assembly from the top of the tank through the access hole.

According to the diagram in the parts catalog, the round plastic piece on your fuel pump assembly is the filter. Not sure what you have from the store.

I checked the information in the shop manual at www.hmaservice.com as a double-check, and it's a little confusing. The procedure pretty much simply says to unbolt the filter and take it off, but clearly shows a diagram the access hole to the fuel pump with no filter evident in the diagram. Look around through the access hole to be sure there's nothing present, but I believe what I have at the top is correct.

replacing the Intake manifold gasket is Avery detailed process. Which includes unhooking alot of wire harnesses, removing all the accessorie brackets on the front of the engine( alt, p/s, a/c,) and in some cases the a/c has to be drained and refilled.The distributor has to be removed and you have to have a scanner to set the timing when your finished. All the manifold bolts have to be tightened to a specific torque. Specials tools are needed for these repairs.This is not one of thpse repairs the average person should attempt. One misstake and you could very easily ruin the motor. If you still wish to try this repair invest in a Haynes repair manual, you can get them at any AutoZone and all the infermation you'll need will be in there, including the torque specs.

sgi.

still not sure?????? guess in the fuse box.... not sure where?

theres one under the hood near the stock intake or under the steering wheel theres a little plastic square that pops off.

I replaced mine a long time ago, so don't remember exactly, but you have to remove the plastic cover on the center council where the shifter is and around the radio itself, I think it can be pulled off, may be screws, like I said long time ago, if it is screws check the area next to your feet for screws, after removing the plastic covers just unscrew the screws holding the radio in place, pull out the radio and disconect the wires.

located on the back side of the engine as you look at it and is accessable the easiest fron underneath