0
use an angle finder
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
How do you figure the hip on a hip roof?
A hip roof, or hipped roof, is a type of roof where all sides slope downwards to the walls, usually with a fairly gentle slope. A square hip roof is shaped like a pyramid. Hip roofs on rectangular houses will have two triangular sides and two trapezoidal ones. A hip roof on a rectangular plan has four faces.
How is trigonometry used in architecture?
Whenever architecture involves the use of lines that are not on the x or y axis, it will involve trigonometry to calculate the length of lines and the angles they make from one another.One example is calculating roof pitch.
How do you calculate a roof pitch of 6 degrees?
A roof angle of 6 degrees = 1.26 / 12 rise or pitch.
Calculate pitch of roof?
Roof pitch is rise and run. So if you have a 4/12 pitch, for every foot of run the roof rises 4 inches.
How many squares of shingles do you need to cover 1900 ft roof?
One square covers 100 square feet, so to cover 1900 square feet of roof you would need 19 squares. However, you also need "starter shingles" and "hip and ridge" shingles, plus you need to have a few extras because of waste from cutting angles. Starter shingles go around the perimeter of the roof as a bottom layer for the first course of shingles. Hip and ridge shingles go, as you might expect, on the hips and ridges. In order to know for sure the exact quantity you would need for the entire roofing job you have to measure all of these areas.
Is a gambrel roof considered a hip roof?
Yes, a gambrel is a form of hip roof.
How do you figure the hip on a hip roof?
A hip roof, or hipped roof, is a type of roof where all sides slope downwards to the walls, usually with a fairly gentle slope. A square hip roof is shaped like a pyramid. Hip roofs on rectangular houses will have two triangular sides and two trapezoidal ones. A hip roof on a rectangular plan has four faces.
Which is cheaper to build a hip or gable roof?
Labor cost for hip roof would be more then gable. Materials are about the same. Hip roof cost slightly more.
Is a hip roof stronger than a gable roof?
a hip roof is stronger than a gable roof because it braces itself and cannot move from side to side.
How do you build on to log cabin with a hip roof?
To add an addition onto a house of any kind with a hip roof, the addition roof must be shorter than the rest. The hip roof goes all the way down to the eaves.
How do you roof a hip roof?
u lay your shingels level to the hip and cut the excess diagonal off then cover the hip after each side is roofed with a "cap"
Is a hip roof better than a gable roof?
Neither is "better" in terms of usefulness or structural efficiency. Hip and gable are primarily responses to design needs. A hip roof is slightly stronger than a gable.
What is a Type of roof with two slopes on four sides?
That is a hip roof.
Definition of a hip and gable roof combination?
A hip roof has a slope on all four sides. A gable roof only has it on two sides. On the short sides of the house the side wall goes up to the point of the roof.
Instructions for swires roofing square?
The figures on the outer edge of the curve are degrees. Use these to set the angle/pitch of the roof. The figures on the inner edge of the curve are a ratio of the length of common rafter per foot or metre of run or span of roof. Take half the span of the roof in feet OR metres and multiply by the figure for the pitch of your roof this will give you the length of your rafter from birds mouth to the centre of the roof. Then make a deduction of half the thickness of the ridge board. at right angles to the bevel . The easiest way to use the bevels/angles from the square is to place the square on a piece of ply or board and mark all the bevels/angles onto the board and then use a sliding bevel/bevel square to apply the bevels/angles to the rafters and other members of the roof. No 1= Plumb & Seat cut for the Hip No 2=Plumb & Seatcut for Common Rafter No 3=Edge cut for the Hip (Mitre) No 4=Edge cut for Jack Rafter No 5=Side cut for Purlin No 4A=Edge cut for Purlin (Mitre) No 6 Lip cut to Purlin .This is the sloping cut which goes under the bottom edge of the Hip where the Purlin abutts to the Hip Rafter
What is the average type of roof on a house?
These days the trussed hip roof is most popular.
Where do you see angles in daily life?
On your roof
