You hold sat button on the remote until it flashes, then press the number you want on the keypad followed by the # sign and record button.
Where do I find the "then press the number" from?
Here's what I found.... Haven't tried it yet, but the guy said this was straight from the manual for the 3100
Make sure to goto the system info screen before changing your 3100 remote address.
Press the Sat button till all the mode key backlights come on. Enter any # between 1 and 15, then press the # key. If done properly the Sat mode light will blink 3 times. Pointing at your 3100, press the record button. Looking at the screen the # in the "Remote Address Field" should match what you entered.
Updated:
Just did this on my own system with a Bell TV tech guy on the phone.
1.First remove the smart card from the receiver.
2.Wait for the System Info page to display on your tv screen.
3.On the remote control press and hold SAT button for at least 5 seconds. 4.When all other lights are on let go and press any number between 01-15
(usually it's 02 or 13).
5.Press the# button
6.Then the record button.
Look at the Remote Address # on the tv screen. is it the number you pressed on your remote? If so you're done. Replace the smart card, wait for the system to reboot and you are good to go.
If it isn't the same number as you pressed on your remote control you'll have to redo steps 3-6 until the number you pressed on your remote is the same as displayed on Remote Address.
Dish Network satellite receivers can be programmed to operate on different remote control addresses. Switching to a different address is necessary if you have 2 satellite receivers or if your neighbor's receiver is set on the same remote address and they are changing your channels. # Press the Mode button until the remote is in the SAT mode. # Press the Address button once (the SAT mode light will start flashing). # Use the numeric key to enter an address between 1 and 15 (do not put a 0 in front of single-digit addresses; 1 is the default remote address). The SAT mode light will stop flashing and stay lit. # Press the Address button again to save the change to the remote control. If you entered a valid remote address, the SAT mode light will blink 3 times. # Make sure the satellite receiver is Powered-off. If not, power the satellite receiver off and wait 15 seconds. # Press the Info button on the front of the satellite receiver. This will bring up the "Important System Information" menu. # Press the red Record button the the remote. The screen will update and the "remote address" listed on the screen will change to the new remote address of the remote control.
Can I change my remote control receiver
remote receiver
To address the remote to the receiver, you do need to be on the System Info screen. You can accomplish this by pressing the Menu button on the old remote 2 times or by pressing the System Info button on the receiver for certain receiver models. Once you are on the System Info screen just follow the instructions below. On a Dish Network Remote Press and hold the sat button down on the new remote until all the buttons light. release the sat button it should be blinking. press the rec button 3 times. your new remote should now work your Dish Network Receiver.
FIXYA.com has the answer under Toshiba 36af42
The DISH remotes don't actually have a specific address button. To access that mode, press and hold the mode button until all the lights on the remote turn on. Once you let go the light will be blinking. From there you can enter a code to program the remote, then press the Pound (#) button!
On Receiver: Open receiver There is a Jumper called Learn Short for 1 second. (Use jumper or Screwdriver) Remove jumper/screwdriver led on receiver switches on. On Remote/Transmitter: Press the button required for that receiver. Led goes off on receiver after a few seconds Push same button selected on remote again. The led will flash on receiver. Procedure complete.
The remote has a radio transmitter built in. The car has a receiver connected to the car locks. The signal from the remote turns on certain circuits in the receiver causing the doors to lock or unlock.
Remote Control Door Lock Receiver
Programming an Expressvu remote control can be frustrating. There are two basic ways of doing in it. The first one involves knowing both your TV brand name and also knowing the proper code to input in your remote. The second method is doing an automatic search. The following is a step by step procedure in how to program your dish network or Expressvu remote.1)Make sure your TV and Satellite Receiver is ON.2)Press and hold TV button until all lights on the side of it flashes. The TV button is the second button on the Top left hand side corner of the remote control.3) Release that button, then press & release RED Button. You will notice TV button is stays on. If, it doesn't stay ON, you must repeat step 2 & 3. Otherwise, your batteries are low, you MUST change then.4)Press and release the UP Arrow Key on the remote until TV turns off. Notice the UP arrow key button is the button below the volume keys (Stop button for VCR.)5)Make sure you are aiming remote control to TV while pressing and releasing UP arrow key button. When you find the right code, the TV will turn OFF.6) Immediately after, TV turns off, press #key.
comcast remote code for Yamaha receiver
the remotes have an embedded serial number the receiver on the opener has has a button you press to make that remote a part of its friendly list. just push the button on the receiver while pushing the button on the remote