0
How do you go about taking a crossmember or even the engine mount housing out of a 1985 Mercedes 300td?
Wiki User
∙ 12y ago
i would advise you to get a shop manual by haynes, or others before undertakeing a projext like that, can be found on eBay or amazon, or barnes and noble. good luck !!! n0rt
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
Why does my mileage still shows on the speedometer of your Mercedes sprinter van when the engine is of?
Try putting the key in the ignition and taking out quickly, and or lubricate the ignition lock mechanism. it worked for me.
Thermostat location on 99 grand am?
Follow the upper radiator hose to the engine. Where it connects to the engine is normally the location of the thermostat housing. THAT IS NOT CORRECT. I LEARNED THIS BY EXPERIENCE. IT IS UNDERNEATH THE ENGINE AT THE WATER PUMP. I AM STILL WORKIN ON MINE SO NOT EVEN SURE YET THE BEST WAY TO REPLACE IT, BUT DONT WASTE YOUR TIME LIKE I DID TAKING APART THE HOUSING NEXT TO THE POWER STEERING PUMP
Is the crossfire made by Mercedes?
Sadly, it somewhat is. The engineering is mostly from Mercedes. Stupid Chrysler merger messed up Mercedes quality, and they are taking German engineering along with them.
Will taking out the two cadillac converters and putting a straight pipe on my mercedes e430 damage my car?
Taking out the two Cadillac converters and putting a straight pipe on your Mercedes e430 will not damage your car.
How do you change the engine coolant temperature sensor a 99 grand prix 3800 engine?
The coolant temp sensor is located just under the thermostat housing. It is not easy to get to a stubby 19mm wrench or a deep socket with a swivel helps. Sometimes taking off the radiator hose and housing makes life a little easier. Hope this helped. Mike
Where is the thermostat for a 94 Chrysler Lebaron convertible located?
Follow the hose from the top of the radiator back towards the engine, where it connects is the thermostat housing, this can be removed by taking out the 2 bolts. - remember to replace the gasket!
Is the housing industry elastic or inelastic?
It is inelastic due to houses taking a long time to build so there will be a short supply of housing. there are also no alternatives to housing. There is but that is if you want to become homeless.
Can you take the housing off the blackberry?
You can take the housing off but it involves taking your whole phone apart try looking on a blackberry website :)
What has the author David W Sheatsly written?
David W. Sheatsly has written: 'Taking stock' -- subject(s): Housing, Housing surveys, Statistics
How does globalisation affect housing?
companies would by houses and use them for their companies use, taking away housing fromlocals who need these houses for their daily living
How do you remove an automatic Chevy one ton transmission?
You need to unhook the shifting linkage which typically is located on the top left side of the transmission then to keep the job clean you need to drain your transmission fluid by taking off your transmission pan. when you get that drained there should be 10 to 12 bolts by your bell housing which is where that transmission connects to the engine. after that you have to unhook your rear drive shaft if its a 4x4 youll need to remove the front one also. then there will be a cross brace. looseen up the bolts but don't take them all the way out. there also will be two bolts in the center of the brace take those bolts out then get a jack under the transmission and jack it up till the mount under the transmission is free then take the bolt out of the crossmember then take the crossmember out then let your jack down slowly
How do you replace the thermostat located on a 1992 Oldsmobile Cutlass?
Some engines are easier than others. Follow the upper rad hose from the rad to the engine and there you will find the housing for the thermostat. take the 2 bolts holding it out after taking the hose off and when replacing it make sure the spring goes toward the engine.
