If the axle is pulling out of the trans, you proably have a failed motor mount. That lets the engine and trans move around to much.
The difference is "soft seated" or "metal seated". Soft seated valves are used in gas applications were any leakage is absolutely not tolerated. The materials used are Teflon or ceramic. Metal seated valves can have very tight shut-off, it all depends on the coating, pressure in the line, and the lapping of the surfaces.
seated or sitted
A person who is seated or sitting.
The obvious answers would be that it is not in correctly and seated, or it is not correctly adjusted for 0.004 - 0.006" of clearance.
Seated Lincoln was created in 1911.
Deep seated
Ignition Lock CylinderRemoval & Installation1. Disconnect the negative battery cable.2. Detach the key warning chime connector.3. Turn the key to the RUN position.4. Place a 1/8 in. wire, pin, or small drift punch into the upper steering column shroud under the lock cylinder. Depress the retaining pin while pulling the lock cylinder out of the column.To install:5. Install the lock cylinder by turning the key to RUN position and depressing the retaining clip.6. Insert the lock cylinder until it is fully seated and aligned with the inter-locking washer.7. Turn the key to the OFF position, allowing the retaining pin to properly seat.8. Install the 2 shroud halves and retaining screws.9. Connect the negative battery cable.10. Check for proper starting in PARK and NEUTRAL.
Ignition Lock CylinderRemoval & Installation1. Disconnect the negative battery cable.2. Detach the key warning chime connector.3. Turn the key to the RUN position.4. Place a 1/8 in. wire, pin, or small drift punch into the upper steering column shroud under the lock cylinder. Depress the retaining pin while pulling the lock cylinder out of the column.To install:5. Install the lock cylinder by turning the key to RUN position and depressing the retaining clip.6. Insert the lock cylinder until it is fully seated and aligned with the inter-locking washer.7. Turn the key to the OFF position, allowing the retaining pin to properly seat.8. Install the 2 shroud halves and retaining screws.9. Connect the negative battery cable.10. Check for proper starting in PARK and NEUTRAL.
Ignition Lock CylinderRemoval & Installation1. Disconnect the negative battery cable.2. Detach the key warning chime connector.3. Turn the key to the RUN position.4. Place a 1/8 in. wire, pin, or small drift punch into the upper steering column shroud under the lock cylinder. Depress the retaining pin while pulling the lock cylinder out of the column.To install:5. Install the lock cylinder by turning the key to RUN position and depressing the retaining clip.6. Insert the lock cylinder until it is fully seated and aligned with the inter-locking washer.7. Turn the key to the OFF position, allowing the retaining pin to properly seat.8. Install the 2 shroud halves and retaining screws.9. Connect the negative battery cable.10. Check for proper starting in PARK and NEUTRAL.
Ignition Lock CylinderRemoval & Installation1. Disconnect the negative battery cable.2. Detach the key warning chime connector.3. Turn the key to the RUN position.4. Place a 1/8 in. wire, pin, or small drift punch into the upper steering column shroud under the lock cylinder. Depress the retaining pin while pulling the lock cylinder out of the column.To install:5. Install the lock cylinder by turning the key to RUN position and depressing the retaining clip.6. Insert the lock cylinder until it is fully seated and aligned with the inter-locking washer.7. Turn the key to the OFF position, allowing the retaining pin to properly seat.8. Install the 2 shroud halves and retaining screws.9. Connect the negative battery cable.10. Check for proper starting in PARK and NEUTRAL.
Ignition Lock Cylinder Removal & Installation 1. Disconnect the negative battery cable. 2. Detach the key warning chime connector. 3. Turn the key to the RUN position. 4. Place a 1/8 in. wire, pin, or small drift punch into the upper steering column shroud under the lock cylinder. Depress the retaining pin while pulling the lock cylinder out of the column. To install: 5. Install the lock cylinder by turning the key to RUN position and depressing the retaining clip. 6. Insert the lock cylinder until it is fully seated and aligned with the inter-locking washer. 7. Turn the key to the OFF position, allowing the retaining pin to properly seat. 8. Install the 2 shroud halves and retaining screws. 9. Connect the negative battery cable. 10. Check for proper starting in PARK and NEUTRAL.
No. If a woman is seated when the gentleman is introduced to her, she remains seated. If the woman is standing, it is not necessary for her to be seated. When a woman is introduced to a seated man, however, he is expected to rise.