0
well i hate to answer a qestion with a question but, it depends on the block, the wall type etc. but providing that you are laying 8" block with nominal dimesions of 8"x8"x16" and the radius is "soft" meaning a radius where the inner most corner of the block has a 1/16"to an 1/8" morter joint, and the outer moter joint of 3/4" or less. you start from a point designated by a dot on the top of a well driven wooden stake(meaning that the stake won't wiggle ,or foul the line point). after you drive the stake find the point as close as you can so that a set distance from the point on the stake to any points the wall must reach will meet very close, closer the better, but one can make up small inconsistencies with block(important to "lay out" as best as you can, it will make it easier) now drive a small nail into the point on top of the wooden stake, this is the point you will be working from.using a good tape measure plot a radius on the footing or substrate. I like to draw a line on the footer with a fresh black maker( small head). and once one has a good mark spray orange marking paint over the black line. it will increase it's visibility and water proof it some. now, there are two ways to lay the block in radius. option 2 is my choice and is probably easiest. but it incroaches on the line(remember this) 1, have the center of the block touch the line you have marked, making sure that each joint gap is even and consistent. so that the wall will be on the outside of the line. 2, have the left and right edges of the block touch the line making sure that the inside morter joint be kept even. the joint width will be determined by the radius.but be sure to have a joint no less than about an 1/8". Now if for whatever the reason your radius is "tighter" than the block will allow by this method the "lay out" will be the same however every block can have some of the cell either chisseld off, or sawn off with a cut off saw and a diamond blade. how much is once again determined by the radius one is trying to obtain(cut off only what you have to, no more). if you cut the block more than say ,the ear off the block gradually starts losing strength, but a block wall can be filled with a soupy mixture of concrete or morter mix to give it strength. In the event that the radius is extremely tight, there are specialty blocks that you can buy that are more of a diamond shape but in some regions they are harder to get than others. NOTE : don't foget to add reinforcement wire and wall ties if your adding brick to the face. I really hope this was helpful.
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
How do you lay cinder blocks?
one at a time
How do you lay down on your bed?
You place it like a regular block, note that it is two blocks long and it will place the foot of the bed where the cursor is, so will be unable to place it if something is obstucting the block next to that, say you were facing a wall and tried to place it on the floor right next to that wall.
When do Italian wall lizard lay there egg?
In the wild Italian wall lizards lay their eggs when it's in summer or in spring it has to be hot for them to lay their eggs. In captivity it can be any time just keep the incubator ready.
Are the intestines proximal to the abdominal wall?
Yes , they lay adjacent to the abdominal wall ; see related link .
When is a plaster wall toxic?
when chickens lay golden eggs
How many glass block can a mason lay in one hour?
100
How many blocks can a block layer or mason lay in a day?
150
How many eggs does the common wall lizard lay?
The common wall lizard lays 3-11 eggs
What are the masonry beams?
A masonry beam is more often called a "bond beam." This is where a block is cut or manufactured with a slot to lay down one or two pieces of rebar down inside the block horizontally. The blocks are filled with grout and this adds horizontal strength to the wall by tying the vertical cells that are filled with grout to the horizontal cells that are filled with grout, creating a grid making the wall much stronger. www.masonryworktools.com
How do you build a block wall that is way out of level?
starting on the low ground side, dig a trench the full length and after pouring the concrete to almost ground level, start with your first block and as it heads into the trench, come back one half of a block and again pour the concrete to near ground level and lay another block and continue doing this until you reach the end. You will find that on your first course you will have only one block on one end and several on the other depending on how much out of level the ground may be. Hope this helps.
What lay outside the wall of the Mycenaean palace?
Large farms, or estates, that belonged to the nobles.
How do you build a bench press out of wood?
If you don't care about visual appeal, the easiest thing to do is to lay a large sturdy board across two cinder blocks. Make sure that the board is strong enough to support the weight you are using, and that the cinder blocks are on their sides so that they don't fall over when you're using the bench.
