To lower the soil pH, add more acid to it by adding 1.2 oz. of ground rock sulfur (another readily available sample) for every square yard of soil in gritty soil conditions, or add 3.6 oz. if your soil is more clay based.
Short answer is you can't. Long answer is lowering ALK is a process. You add acid which drops pH and converts bicarbonate (which is the main component of ALK) to carbonic acid (basically carbon dioxide dissolved in water). You then wait for the CO2 to gas off (aeration speeds this up) and whenit does pH rises since you have decreased the amount of carbonic ACID (operative word is ACID) in the water. If Alk is not low enough the processis repeated. It is never a good ides to drop the pH below about 7.0 each time you add acid to lower the pH for various reason so this process can take several day or longer to complete (depending on how much you have to reduce the ALK and the amount of aeration you are able to provide to speed up the outgassing.
The old adage that "walking acid lowers pH and pooling acid with the pump off lowers ALK" is simply not true and has been scientifically disproven, not to mention potentially harmful!
My the addition of an acid
With Muriatic acid
use muratic acid to bring down Ph and TA
It could be, but sounds more like hi alkalinity. Check your TA ( total alkalinity ) It should be between 80-120 ppm. You can bring it down using muriatic acid if you need to.
1. M-Alkalinity (also known as Total Alkalinity) measures the amount of carbonate, bicarbonate and hydroxide present in terms of "ppm as calcium carbonate". ( M-Alkalinity measurement is based on a sulphuric acid titration using a Methyl orange indicator that goes from yellow at a pH of 4.5 to orange at pH of 4.4 at the endpoint.) 2. P-Alkalinity measures the amount of carbonate and hydroxyl alkalinity present in terms of "ppm as calcium carbonate". P-alkalinity is measured down to a pH of 8.3. The M-alkalinity is measured down to a pH of 4.3.
1. M-Alkalinity (also known as Total Alkalinity) measures the amount of carbonate, bicarbonate and hydroxide present in terms of "ppm as calcium carbonate". ( M-Alkalinity measurement is based on a sulphuric acid titration using a Methyl orange indicator that goes from yellow at a pH of 4.5 to orange at pH of 4.4 at the endpoint.) 2. P-Alkalinity measures the amount of carbonate and hydroxyl alkalinity present in terms of "ppm as calcium carbonate". P-alkalinity is measured down to a pH of 8.3. The M-alkalinity is measured down to a pH of 4.3.
1-2 gallons of muriatic acid will break down the buffer solution(alkalinity in the water). Will then probably have to raise pH back up
Alkalinity is common baking soda. Hatawa
Use the "acid demand" solutions in your test kit to determine how much acid is needed to bring the pH down to 7. There should be a chart in the test kit that shows how much acid to add depending on the gallonage of the pool. It may take several weeks of this to bring the total alkalinity into desired ranges. Lowering the pH more than that may strip copper off the heat exchanger in the heater. Typically you will knock 10 points or so off the TA reading every time you do this.
its the song: bring me down by Pillar
Tonight's performance will bring down the house. Please bring down my hat from the attic.
phenolphthalein alkalinity is due to hydroxide n carbonate salts in water...nd total alkalinity is mainly due to bicarbonate salts in water..
what can I take to bring down my period
add some form of alkalinity booster for sure. bring it too about 110ppm, chlorine has a naturally high pH, but the higher alkalinity addition will stop acidic compounds from attacking the pH any further. depending on how low the pH is though you may have to add a pH booster, take your water into a pool shop for an in depth water analysis.