A rubber band boat works much like a rubber band airplane. First you need to build the boat itself. Then you need to make a propeller. The propeller shaft needs to run through the inside of the boat, not below the boat. With the prop below the water. The propeller shaft should not go the full length of the boat. About halfway through put a loop in the shaft. Then to the front of the boat attach a rubber band. Then run the rubber band through the loop in propeller shaft. Now twist the prop and the rubber band should twist around and around. When it's good and tight let go and the propeller should spin. Allowing the boat to move forward in the water.
Mind you the shaft needs to be a thin piece of metal, as it will be difficult to make it water tight.
First you need to build the boat itself. Then you need to make a propeller. The propeller shaft needs to run through the inside of the boat, not below the boat. With the prop below the water. The propeller shaft should not go the full length of the boat. About halfway through put a loop in the shaft. Then to the front of the boat attach a rubber band. Then run the rubber band through the loop in propeller shaft. Now twist the prop and the rubber band should twist around and around. When it's good and tight let go and the propeller should spin. Allowing the boat to move forward in the water.
A rubber-band is made out of rubber because rubber will make it hold things nice and tight.
You build a basic car, with a body and a way to support the front wheels and the back wheels. Each set of wheels should be firmly attached to an axle, maybe a piece of dowel, so that when the axle turns, so do the wheels. Then you need some way to attach the end of a strong rubber band to the middle of each axle so that when you rotate the wheels, the rubber band winds around the axle and stretches tight. You can do this with a small nail or screw put carefully through the dowel. The best way to wind the wheels is probably to push down on the car while you push the car along a surface, like carpet. once the rubber band is really tight, you let the car go, and the stored energy in the rubber band unwinds the axle, and off goes the car You don't have to have the band wind around both axles ... you could make it either just frontal drive or rear-wheel drive, but it probably goes better if you use both axles. You could also use two rubber bands, one for the front wheels and one for the back wheels, with the ends of each rubber band fixed to the middle of the car. Remember, the car will go fastest and the most distance if you use a really BIG strong rubber band, and can wind it up around the axles really really tight. But if you make it TOO tight or too strong, the car or the axles might break when you wind it up, which is not good and really annoying. Another way of making a car like this is to make it like the rubber-band powered toy airplanes. Make a light frame with 4 wheels, and buy a little toy propeller or take it off a toy airplane, then wind up the rubber band by winding the propeller. Then when you let go the propeller, it will drive the car along.
you can make a rubber out of rubber and you can make lots of things really. I can't tell you all the things because you can make so many.
Yes yes it does cause you use that rubber to make tires for your car
vulcanization process of rubber and vulcanization process of rubber.
Rubber powered airplanes fall into three types.The first is to use a rubber band as a sling attached to the front of the plane. When stretched and released the contracting band moves the plane forward and it soars upwards based on the aerodynamics of the wing.The second rubber band powered plane uses a twisted band attached to the propeller. the realising torsional energy as it unwinds turns the propelled and pulls the plane forward and it soars upwards based on the aerodynamics of the wing.As an alternate, a mixture of rubber powder and oxidant can be used in a rocket engine to thrust the plane forward.
how do you make a rubber band car
A rubber-band is made out of rubber because rubber will make it hold things nice and tight.
Something light and strong for the car (cardboard box? plastic bottle? Styrofoam?). The biggest and strongest rubber band you can find.
i don't know a hundred, but you could make a rubber band gun, and a rubber band ball, or a rubber band chain. just look on youtube for instructions.
By making rubber and putting it around a cyllindrical figure to make a band making it as thin or as wide as you like.
Here are some easy-to-follow steps on how to make it:Materials:Two rubber bandsSteps:Step 1. Take rubber band #1 and put it through rubber band #2.Step 2. Fold rubber band #1 around rubber band #2.Step 3. Take the newly made rubber band and put it around your wrist.Hope I helped =)
vibration
good question
A rubber band slingshot can be made with a rubber band and a stick. The stick needs to be in the shape of a Y. Put the rubber band around the two small pieces of the stick and you will have a slingshot.
I don't think you can make a silly band with a regular rubber band I think in the factory where they make silly bands they have a special machine to shape them. they only thing you going to get if you do make one a home is a circle. because that is the shape of the rubber band.
Stretch a rubber band at different lengths