How do you make element 115?

Answer 1

The Lighter Side

Keeping in tune with the gravity of things, this little experment may get

you off the ground. I have not done this yet.

Using the Jack Keller process and some of Dr. Walter Russell's

illuminations, a bit of J. C. Maxwell EM equations, some of Dr. Roberto

Mounte's work, the Keller transmutations have been proven to work...

Merlin has just moved the process down the Periodic chart, or increased

the operation another octave, to give the higher atomic number (element

Uup115.)

Just like the classic transmutation of O + C = Fe 2nd octave, or more like

the profitable O + C = Pt in the 7th octave .... So by pulling with a

noble gas like Ne, Ar, Kr, Xe, or Rn and pushing in to Bi with U, Ra,

Th...

Since there is no Uup115 seed material aviable to the common folk, we will

use I, Ge, with Bi to seed and start the reaction and hope that will do.

To find out how to use this new element take a look at the

{http//:boblazar.com } Bob Lazar home page.

Things that need to be built

1. Burn chamber: start with a # 2.5 coffee can and some Cu wire #0

gage. Wind the wire 2 turns about the bottom 1/3 of the coffee can,

and weld the ends of the wire together. Make sure that the wire is

not too tight on the can.

2. Cover for the burn chamber: use the metal lid cut from a #5 coffee

can, punch 2 holes in the lid,one in the center and another about

1.5in. from the first hole. Find a ceramic small insulator to

withstand about 5-10 Kilovolts for the center hole. This is the

igniter. Insert a steel wire 8in in length thru the ceramic

insulator. For the other hole, find a length of steel 1/4 in. tubing

at an auto parts store, bend the tube at say 90 degrees to give 3in

and 12in sides. Insert the short end 1in. thru the lid's other hole,

and tack weld the tube to the lid.

3. Build an igniter power supply having 5-10kv output voltage. Use an

automotive spark coil, capacitor 4-20 mfd, switch, battery, Hi voltage

wire. Construct a charge/discharge type HV pulse source.

4. Obtain a balloon that will hold about 2-3 cubic ft., also neon gas

to fill the balloon, find a valve (fish tank type,) and plastic tubing

which fits the steel tube on the lid, the valve, and fits and the

stopper in the balloon. (Neon is available at a "tube art" store.)

5. Mix SrNO sub 3 70% wt.,, S 7%wt.,, and C 23%wt. To about 2/3

of a coffeecan measure, add about 1oz. of Bi and .01gr. of a stable I

compound { ICl } and .01gr UNO sub 3. MIX and MIX again. Pour into

the # 2.5 can, DO NOT PACK, fill can to 2/3 from top.

6. In a large metal bucket place the can, mix, and just lay the lid on

top, so that the neon gas can fill the coffee can. Also bend the HV

wire end within the can so that it comes with in 1/8in of the side of

the can, so that it can arc through some of the mix and ignite it.

7. Hookup the igniter wire to the power supply (We will later toggle this

switch to fire the mix.)

8. Set the valve for the neon gas to just flow very slowly. Allow it

to purge the air out of the can.

9. FIRE the mix ... BE SURE that the lid is NOT held down!!!! Stay at

least 50 ft from the reaction, as there could be a large amount of

radiation gamma and Beta rays...

10. The button of stuff at the bottom of the can will have Uup115 and Bi,

also some Pt group, you must separate somehow.

Some Notes that may help:

--- Kickers: these are elements that will increase the yeild.

Ge (germanium,) I (iodine,) Ar (argon,) Kr (krypton,)

and U (uranium) will do this.

--- There are some elements that will cause an adverse reaction:

proton emitters like Ta (tantalum) and Re (rhenium,) they

could create small BLACK HOLES or Singularities or level an

area. Protons and Uup 115 make antimatter, mix this with

Hydrogen and you have nothing left.

---Basically this is the Jack Keller system, but modified to push

the transmutation beyond the Platinum / Gold group; the next

level down on the Periodic Table.

--- note: #2.5 can is about 6in. by 3.5in. dia. And #5 can is

about 7in. by 5.5in. dia.

The problem is to ID the resulting material...

No Problem in ID the resulting material you can borrow my TransTeleologicalThermodynamicSequencer (it only takes 52 articulated lorries to carry it, and a staff of 304 to work it).