SONY
You should not have to program this remote.... although it says universal on it. This is an original remote and should work when you put the batteries in. For T.V viewing, just push the t.v button on the top of the remote then power/on-off .... wait for the light, then the sound, then begin with your normal activities.
I want to tell you what just worked for me... 1. Turn the component on that you want to program 2. Press and hold that component key (TV, VCR/DVD, or SAT/CBL) on your remote 3.Press ON/OFF button until your unit turns off. 4. Press Stop button to program the "code" that you remote found to work your component.
YOu must program it as a Toshiba DVD using the AUX button on remote control and the codes 0695 (which worked for me) or 0503, or 1045.Then seperately set up the volume by changing the volume control lock according to directions. FYI... Comcast could not help at all!______________________________________________________That was a helpful answer, thanks.Additionally, based on my own experience a couple of minutes ago, I was able to program the Comcast remote for the Toshiba TV/DVD combo (Tosh model MD19N1, fyi) by using the AUX button & treating the TV/DVD combo as a DVD, as the answer above suggested. But the code that worked for me was the Toshiba DVD code listed in the Comcast remote pamphlet (specifically, code #20695), rather than the codes stated above. But the answer, above, to use the AUX button & treat the TV/DVD combo as a DVD is what set me on the road to being able to program the remote. Also, the answer suggested above about programming the volume for the remote, by just following the Comcast remote instructions for "unlocking" the volume was exactly right. Also, fyi, none of this programming of the Comcast remote messed up TV/DVD operation by the original remote I have for the TV/DVD. I just didn't want to have to be juggling two remotes all the time.Thanks alot for that answer above. (11/5/10)
0178 this did not work for me. 0134 LG code worked for me.
This will vary by year of TV but this works often. Make sure to have the TV remote in hand. Press the menu button then choose Setup. From there choose auto program. If it ask you to select a source choose Air or cable. Then there should be an auto program option to press for the channels get programmed.
press little button on the xbox then on the same little button on remote shows it on instructions
I had the same problem with my proscan 40lc45s and the remote from comcast. I called proscan at 888-977-6722. They were very helpful. Codes 10178, 10029, 10030 and 10019 all worked. Hope this helps
how to program my tv with the RCA D 770 - universal remote control which has no code search button
PROGRAM A TRISONIC UNIVERSAL REOMTE TS-rc 411
2.7 seconds.
Hold the button you want to program and then hold the on/off button at the same time it should program
To program a GPT universal remote control, hold down the power button at the same time with the button for the device that is going to be programmed. When the other buttons on the remote blink, let up and press on the power button again. The device should turn on. If not, repeat the process.
You can program the remote start by holding the start button down for 10 seconds. The start light will illuminate. With the start light illuminated hold the start button down until the engine start.
no u cant dumba**
there is no cable button on this remote what do i push to hook cable its says hit cable button
To program a 2007 GMC Envoy remote, close all the doors. ?æInsert the key in the ignition while holding the unlock button on the drivers side. Turn ignition from on to off twice. ?æNow release the unlock button. ?æThe fob is ready to program.
If you want to add a remote, press the "set" button on the power unit until the green light blinks, then press the button on the remote. If you want the unit to forget all old codes and accept only the new remote, hold the "set" button until the green light stays on solid, then press the remote button.