How do you program an RCA d770 universal remote if you don't have a code search button?
Answer . If you know how to program the D770 remote for device buttons other than the DVD device button, then you shouldn't have much of a problem. However, I suspect that you are unaware of the procedures for programming the remote (as I was before I researched it), or your DVD player is newer t…han the remote and/or the remote just simply does not contain the code for your DVD player, or the remote's batteries are dead or low, or the DVD device button on your remote is not working (which can be tested by noticing if the red LED under the ON/OFF button lights up when the DVD button is pushed). Under the rca.com website, I found the following webpage that shows the instruction manual in pdf format for the RCA D770 remote:. http://download.ethomson.com/english/RCA/ACCESSORIES/IB/D770.pdf. If the remote is working properly and it contains the code for your DVD player, then I am pretty sure that following the instructions from the said manual should solve the problem. However, aside from directly entering the code (which I found did work for me), when I tried (more than once) using the Automatic Code Search procedure as shown on page 5, it never worked...Which I thought I'd mention since some people might have the same problem occur, and I had found on my own a procedure for a solution to this problem that is not even mentioned in the said instruction manual. It is as follows:. Turn on the device you want to control. Press and hold the button you want to program followed by holding down the ON/OFF button. When the red LED lights up, then release both buttons. While pointing the remote at the device, instead of doing any pressing of the PLAY button, just press the ON/OFF button until the device turns off. You need not wait 5 or more seconds between presses as you'd need to do when pushing the play button, but do not press the ON/OFF button way too fast. After, or upon, each press of the ON/OFF button, the LED blinks (goes off and immediately back on) and it is after this blink (that is, after the LED goes back on) when you can then press the ON/OFF button again. Don't worry, the blinks occur anywhere from about 1 second (which would be the max), to a fraction of a second, down to even the exact moment the ON/OFF button is pressed. Be careful though, so as to be able to stop when the device turns off...that is, do not press the button again after the device turns off. For, if you overshoot and press the button, even once, after the device turns off, you more than likely would have to hold down the CLEAR button until the LED goes out (and which clears the procedure), and then start the procedure over. Anyway, after the device does turn off, you then hold down the STOP button until the LED goes off, and your set to go.. Comparing both procedures for Automatic Code Search, when the PLAY button is used to search, you only need to press the PLAY button a maximum of 20 times because each press sends, not just one code signal, but a group or set of different code signals in rapid succession to test which one turns the device off. If one set of signals do not work then you press the PLAY button to send another set. That is why you need to wait 5 or more seconds between presses. Although using the procedure in pressing the ON/OFF button requires a much less wait between presses (since only 1 code signal is sent for each press), accordingly, you would need to press the ON/OFF button a greater number of times to get through all the codes (Maybe around 100 presses or code-signals?).. My only idea as to why my pressing the ON/OFF button for the code search worked while pressing the PLAY button did not is that the group of different codes sent after pressing PLAY were sent too close to each other...at least where MY television's ability to decipher them is concerned.. And finally, just to let you know, the codes in the said manual for the remote are 4 digit codes and different from the 3 digit codes that are listed in web pages that show general codes for remote controls. Fop example, compare the code in the said manual with the codes I found for the same devices in web pages otherwise...1 of which I listed for you as follows out of the many I found on the net: http:/www.thompsontv.com/rcarc.html. I found that all the web pages - except the web page for the D770 remote's manual - had the 3 digit codes that were all the same and consistent for the same devices; the said manual's codes were 4 digit and different. However, I put in and tried the associated 3-digit code, and then put in and tried the associated 4-digit code, for my TV and they both work the same!. Well, I thought I'd leave you with this interesting info just in case you might need it. Good Luck, Vullin. ( Full Answer )
\n. \n Answer \n. \nYou can go RCA remote codes at RCA.comm. or something like that.Match you model or part number or picture.\n. \n. \n Answer \n. \n1. Manually turn on the component you want the remote to control.\n. \n2. Locate the codes for your brand in the code list.\n. \n3. Pr…ess and hold the component key you wish to program. The ON-OFF key turns on and stays on.\n. \n4. While holding the component key down, enter your first four-digit code. After the first number is pressed the ON-OFF key will turn off. When the fourth number is entered the ON-OFF key turns back on.\n. \n5. Release the component key. If the ON-OFF turns off, you have enter the correct code.\n. \nNo, wrong code?\n. \nIf the ON-OFF light blinks 4 times it is the wrong code. Repeat the process.\n. \n . Some TV codes**\n . \nJVC\n1012, 1028, 1029, 1051, 1054, 1065, 1080, 1096\n. \nMagnavox\n1004, 1006, 1008, 1019, 1036, 1041, 1044\n. \nMotorola\n1003, 1092\n. \nPhillips\n1003, 1004, 1008, 1012, 1019, 1021, 1019, 1021, 1031, 1036, 1041, 1044, 1059, 1062, 1075, 1087, 1089, 1094, 1102, 1103, 1110\n. \nRCA\n1000, 1003, 1004, 1005, 1006, 1019, 1053, 1054, 1056, 1057, 1060, 1076, 1077, 1079, 1082, 1089, 1098, 1112\n. \nSamsung\n1004, 1005, 1006, 1007, 1012, 1015, 1019, 1030, 1035, 1039, 1066, 1082, 1089, 1093, 1104, 1114\n. \nSharp\n1004, 1006, 1010, 1012, 1013, 1040, 1061, 1089, 1092, 1093, 1111\n. \nSony\n1002, 1017, 1069, 1074, 1088, 1108 ( Full Answer )
RCA codes for Hughes satellite receivers . \nTry one of these codes: 5077, 5083, 5090
This is what worked for me:. Manual Code Search and Entry. 1. Manually turn on the TV 2. Press and hold the TV button The illuminated ONâ¢OFF key turns on and remains on. 3. While holding the component key down, press and hold the ONâ¢OFF key. The illuminated ONâ¢OFF key turns off.… 4. After holding down both keys for three seconds, the illuminated ONâ¢OFF key turns back on. 5. Release both keys. The illuminated ONâ¢OFF key remains on. TIP: Throughout the programming of each key, be sure to keep the remote pointed at the IR sensor of the component you are currently programming the remote to control. 6. Press and release the ONâ¢OFF key repeatedly until your component turns off. Each time you press the ONâ¢OFF key, the illuminated ONâ¢OFF key blinks, and the next code in the list is sent. This process continues until all of the codes in the Code Lists have been searched. If your component turns off, you have found the correct code. TIP: Because there are so many codes, you may have to press the ONâ¢OFF key many times-possibly up to 200 times. 7. Once you have found the correct code, you must save the new code by pressing and releasing the STOP key. The illuminated ONâ¢OFF key turns off. You must press the STOP key to save the code or the correct code will not be stored! 8. To confirm that the component key is programmed with the correct code for maximum functionality, test the component. Attempt to control a variety of the component's functions with the remote. If some of the features of your components do not work, try programming the remote with a different code in the list until you find the code that allows the remote to control the majority of your component's functions. Different codes can provide different levels of functionality.. Good Luck. Jack ( Full Answer )
i found this on yahoo Emerson 18 Fisher 16 Funai 05 GE 06, 08 Goldstar 17 Hitachi 14 JVC 15 Magnavox 08, 10 Mitsubishi 13 Panasonic 12, 20 RCA 06, 08 Samsung 19 Sanyo 16 Sharp 01, 02 Sony 09 Technol Ace 03 Toshiba 11 Zenith 04, 07 ANSWER: The codes from the RCA pa…mphlet are: SHARP - 2001, 2012, 2018, 2040, 2084, 2092, 2113. You will find that codes are only unique to the brand of universal remote you bought. This means that the right code for an RCA remote will be worthless for a GE, Zenith, Philips, etc brand of remote. Universal remotes generally work fine for TVs and VCRs that are used for playing only but are usually very unsatisfactory for many VCRs used for timer programming. Often the clock can't be set so the VCR timer can't be programmed due the memory or enter button not functioning [and on and on]. So for other than "play" mode, you need a remote for that exact VCR. Google "1-800-remote" [expensive] and get the original remote part number and it's generic number. Then, Google "Ebay remote control part #-------- & #-------." You may be suprised how reasonable you can buy a used or generic remote control specifically for your VCR. That way all your functions will work correctly. bestoflucktoyou Mike ( Full Answer )
I have an RCA DVD Recorder, model DRC-8310 that includes this remote control. I am including a link here that will take you to a site that has an Adobe PDF format user's manual for the DRC-8310. I am also including a link from my website as well. We will have to see whose remains available for the l…ongest time. The manual contains a chart of the device codes the remote control understands, instructions on how to program the AUX button for other devices, volume punch-through and more, as well as instructions on the 2 modes of programming; Direct Entry and Automatic Search modes.. Link provided by RCA (Link to a 3rd party document archival site): http://220.127.116.11/public/DRC8310_IB.pdf. Link from my website: http://www.icsaz.com/Files/RCA_DVD_Recorder_Model_DRC8310_User_Manual.pdf. Any questions you might have can be answered simply by accessing email support via my website. ( Full Answer )
Make sure the device is on. Hold down the tv (or whichever device your trying to program) button first and then the power button simultaneously until the red light stays on solid. Then press the power button, it will flash one time, and keep pressing slowly letting it flash until the device turns of…f. Then press the stop button...and it is programmed. ( Full Answer )
Programming RCA model RCR660 (no code search button) . While following these instructions, keep the following in mind:. device = the component you wish to control with your remote (TV, DVD, VCR, etc.) . DEVICE = the button labeled for the component you wish to program . Turn on the device you… wish to program. . Turn off all other devices in the general vicinity. . Press and hold DEVICE . While holding DEVICE down, press ON/OFF and hold them both down until the LED turns on for that device. . Release both buttons. . Point the remote at the device, press and release PLAY and wait 5 seconds or until the LED stops flashing. . If the device does not turn off, then continue to press PLAY and wait the required interval (for a maximum of 20 times) until the device turns off. . When the device turns off, press REVERSE, wait 2 seconds and continue doing this until the device turns back on. . To finish programming, press and hold STOP until the LED turns off. ( Full Answer )
This unit is basically the same as the D770 universal remote. You can download instructions from RCA at RCA.COM. The Only difference is there is no light below the ON/OFF button, the individual buttons will light, and when you hold down the device key and the on/off together all lights will come o…n. ( Full Answer )
1. Manually turn on the component. you want the remote to control. (TV, VCR, DVD, satellite receiver. or cable box).. Note: If you press an invalid key. during the Manual Code Search,. the remote does not respond and. the LED indicator light does not. blink. If you do not press a valid. Ma…nual Code Search key ( TV ,. VCR , DVD , SATÂ·CBL , ONÂ·OFF ,. GO BACK ), the search times out. after two minutes. When the. search times out, the LED. indicator light blinks four times. and turns off. The last. programmed code under that. component key is retained.. 2. Press and hold the component key. ( TV , VCR , DVD , SATÂ·CBL ) you. wish to program. The LED indicator. light turns on and remains on.. 3. While holding the component. key down, press and hold the. ONÂ·OFF key. The LED indicator. light turns off.. 4. After holding down both keys. for three seconds, the LED. indicator light turns back on.. 5. Release both keys. The LED. indicator light remains on.. Throughout the. programming of each key, be sure. to keep the remote pointed at the. IR sensor of the component you. are currently programming the. remote to control.. 6. Press and release the ONÂ·OFF key. repeatedly until your component. turns off. Each time you press the. ONÂ·OFF key, the LED indicator. light blinks, and the next code in. the list is sent. This process. continues until all of the codes in. the Code Lists have been searched.. If your component turns off, you. have found the correct code. (If it. cycles through and the LED. indicator light blinks four times. and turns off, all codes have been. searched. The Manual Code Search. method is exited.). Press Stop when TV turns off. ( Full Answer )
You have a sylvania personal TV the remote is not working what is the code to use a universal remote the universal remote is a RCA?
I searched the internet looking for a way to program my comcast remote to work on my plain old 32" Sylvania TV. Nothing worked. The codes given by comcast didn't work. I read on another web site (askdave) where people with new Sony big screens were having the same problem. Their problem was solved b…y entering a 1 in front of the four digit number on comcast's list for their TV. I tried this for my Sylvania and the third code in the list worked with the 1 in front of it. Hope this helps. ( Full Answer )
You cannot program an rxe 247047 RCA remote without codes. Thesecodes are what allows the remote to access equipment, such astelevisions and DVD players.?Ã¦
1. Turn on TV. 2. Press and hold CODE SEARCH until light stays lit, release. 3. Press TV button. 4. Press POWER repeatedly (slowly) until TV turns off. 5. Press ENTER. (repeat for VCR & Cable)
Remove the battery cover on the back of the remote and look for the model number ("RCR8153603P" for instance) . Consult list of TV codes for your model via: http://support.rcaaccessories.com/index.html (or search online) . Press and hold the TV button on the remote. LED will stay "ON". . Ente…r the code for your brand of TV into the remote while continuing to hold the TV button down. LED will go out during number entry and turn back on when the last digit is entered. . Release the TV button. LED will flash and go out if number is entered successfully, or flash 4 times if it detects an error. . Press Channel up or down to see if this has worked. ( Full Answer )
If your instructions aren't available, use the link to Thompson's instructions for the RCA remote.
I have a sony TV the remote is not working what is the code to use a universal remote the universal remote is a RCA?
Do you have a universal remote with a cable company i.e. comcast? If so, reprogram the universal remote and the tv remote should work as well. You can find the listing of codes for all manufactors on your subscriber website.
Press "Code Search" button for 5 seconds. When the red light is on release the "Code Search" button and keep pressing the "shut down" button until your TV/DVD turns off. When it turned off press "Enter" button and complete the process.
Each code in the RCR3273 remote control is intended to work with a specific TV, VCR, DVD, Satellite, Cable, or DVR box. TV codes start with 1 and are intended to work with the TV button, Satellite/Cable Box codes start with 5 and are intended to work with the SAT/CB button. All other codes work with… the DVD/VCR button. If you have the code, press the button at the top of the remote that corresponds to your device type (TV, Satellite/Cable, or DVD/VCR/DVR) and hold it for three seconds. The light should stay on. Continue to press this button throughout the programming process. Enter the code for your device. Remember, TV codes start with 1, Satellite/Cable box codes start with 5. Enter all 4 digits in the number. The light on the remove should turn off when you press the first button. If the LED blinks 4 times at any point during code entry, you entered an invalid code. Once you have entered the last digit , the light on the remote should turn back on. Remember to check your work by going through the full complement of remote functions. ( Full Answer )
We tried and tried to do it by the instructions that came with the remote, but we just couldn't get it programmed. Then, on the web, we read instructions from a user which allowed us to program it, and it was much easier. Start with the appliance (TV, VCR) off and turn on. 1. Press the appliance bu…tton (TV, VCR) and the ON/OFF button, holding them down until the ON/OFF button lights up. Release the buttons and the ON/OFF button should stay lit. 2. Then press the play button every couple of seconds until the appliance turns off. 3. Then press the REVERSE button every couple of seconds until the appliance turns on. 4. Then press STOP (on the bottom) to save the programming. 5. UREKA! ****THIS IS THE EASIEST AND BEST TIMESAVER!! Thank you!! ( Full Answer )
The following directions I found worked for me to program my crk76ad2 remote: Turn on the component you want to program. 2 Press and hold both the TV/DVD/ect button and the power button until the light comes on and stays on 3 Press the play button every 5 seconds until the device turns off. A bank o…f ten codes is being sent each time. 4 Press the rewind/reverse button to see if it turns off/on again. Wait 2 seconds and press again until it turns back on.You may have to do this up to 10 times until it searches through the bank of ten codes sent. 5 Press and hold the stop button until the light goes off. This saves the code. Found the instructions at: http://www.wikihow.com/Program-an-RCA-Universal-Remote-Without-a-%22Code-Search%22-Button ( Full Answer )
I'm honestly going to say Throw the thing out, you cant find anymanuals online, every website that says oh we'll give you a manualis bs. I'm sick of it. manuals online doesn't have it theres a linkfor wikianswers that says visit the link at some stupid websitelike manage my life dot com or something… stupid like that no luckso sorry. I'm getting irritated trying to find it too trust me. ( Full Answer )
I want to tell you what just worked for me.... 1. Turn the component on that you want to program. 2. Press and hold that component key (TV, VCR/DVD, or SAT/CBL) on your remote. 3.Press ON/OFF button until your unit turns off.. 4. Press Stop button to program the "code" that you remote found to w…ork your component. ( Full Answer )
go to this website.. http://18.104.22.168/rcaaccessories/RcaaccessoriesProductDetail.do?ACTION_TYPE_ID=ACTION_TYPE_PRODUCT_DETAIL&ACTION_CATEGORY_IDSTR_CATEGORY_4_DEVICE_REMOTES&ACTION_PRODUCT_ID=RCR412B. Scroll down and go to Additional Info and click on the link. You should find all of the codes…. ( Full Answer )
how to program my tv with the RCA D 770 - universal remote control which has no code search button
go to http://www.rcaaccessories.com/rcaaccessories and find your remove control - you can print a new user manual.
You can use the Code Search function to find the code. Hold Code Search for a few seconds until the light stays on. Then press the TV button. Point the remote at the TV and press the Channel+ button until the TV changes channels. There are up to 300 codes so you may have to press Channel Up a lo…t before it works for your TV. Make sure you stop pressing Channel+ as soon as the TV changes and press the Ent key to lock in the code. ( Full Answer )
You should not have to program this remote.... although it says universal on it. This is an original remote and should work when you put the batteries in. For T.V viewing, just push the t.v button on the top of the remote then power/on-off .... wait for the light, then the sound, then begin with you…r normal activities. ( Full Answer )
Such codes are generated by the universal remote manufacturer rather than the TV manufacturer. As such, the actual codes will differ from one remote to another. Regretfully, Olevia TV's (for the most part) use proprietary infrared frequencies. This means that the code for another TV brand will not w…ork with Olevia TV's.. If you are looking for a universal remote, Olevia made a learning remote (model RC-LRN). Amergence Technology Inc. sells them for 39.99. They can be reached at 866-965-3842. ( Full Answer )
To program a Symphonic TV with an RCA RCR-612 universal remote,there are four codes which you can try. Those codes are 1033, 1038,1046, and 1047. To try the codes, press and hold the TV button onthe universal remote. After you enter the fourth digit, the powerlight will turn on. Once the light is on…, release the TV key. Ifthe power light turns off, you have the correct code and can nowuse the remote. If the light blinks, it isn't the right code andyou need to repeat the procedure until you find the right code foryour particular TV. ( Full Answer )
You need to have a Code search button or at least have a list of codes. You can call the manufacturer for a list or a book. Look for a phone number and you will be able to get some help with this problem.
also need code to turn Phillips vcr on and off. or maybe get codes for a russound universal remote to turn on/off Phillips vcr and vizio television. thanks
I have the universal codes to a GE universal for the RCA Tv's it says including plasma and lcd televisions...........They are as follows..........0031 0004 0048 0054 0094 0100 0102 0107 0129 0191 0005 0009 0000 0162 0163 0342 0003 0015 0022 0096 0113 0125 0179 0187 0188 :)
It would depend on the model of the remote, the large majority can and when searching for the model number of the remote, some have 2 model numbers associated with them. If you can't find a number, there are web sites with 1000+ pictures to compare and using their filters you can narrow your search …fairly quick and they have pdf forms with user guides and codes. I always start my search at _ _ _ _ _ _ _.com Also keep in mind if the remote is of an earlier year, say 3-5 years ago, it may not have a code available as I have found many code sheets only list what was available at the time of printing and they seldom upgrade their list. I see the manufactures offering more features that require more circuitry, more buttons and nicer features that include learning, backlit, glow in the dark buttons and even a searching tone for when you just can't remember where you placed it or it fell under the cushions or was folded into the covers ( Full Answer )
You can find instructions for doing this by going to support.philips.com and then navigating to your particular model Philips remote control.
Solution Jumbo Remote with out the code search button. Here are the instructions: Hold the device button you want to program for 3 seconds & release. Push & release the power button & the red light will remain lit. Push the CHANNEL UP button over & over slowly until the device turns off. …When device turns off press OK button. ( Full Answer )
Try with: 0699, 0769, 20699,20769,704 or 052 I could not get it to work with either of them (with slight variations).
Turn on the first device you want to program to the Gemstar remote control. . Hold down the button you want to program, for example "DVD," while holding the "ON/OFF" button until the red indicator light comes on. The remote control is now in programming mode. . Point the Gemstar remote control a…t the device and press the "Play" button. The indicator light will blink for approximately five seconds as it searches the first group of codes. . Press the "Play" button after the indicator light stops blinking to check the first group of codes. Continue doing this until the device powers down. . Push the "Reverse" button and wait approximately 2 seconds. Continue doing this until the device turns on again. . Save the code setting by pressing and holding the "Stop" button until the indicator light stops blinking. . Repeat Steps 1 to 6 for each device you want to program to the Gemstar remote control. Direct Code Input . Review the last page of the RCA Gemstar remote control user manual. This page has a list of device manufacturers. Look up your device's manufacturer to find the remote codes for your device. . Turn on the device you want to program to the remote control. . Press and hold the button you want to program, such as "SAT/CABLE," and use the keypad on the remote control to enter the first code from the list. . Release the button you want to program and press the "ON/OFF" button to see if the programmed code worked. The device should shut off if the code was successful. . Repeat Steps 3 and 4 with the next code on the list until you find a code that operates the device. . Program the rest of the devices you want controlled by the Gemstar universal remote control by repeating Steps 1 to 5. ( Full Answer )
The codes for individual products for the RCR660 can be found at the link below.
well it depends on what country you live in to purchase it its from Australia to north Korea im pretty sure i had put it down
i have a rca remote without any light, have a quasar tv, how do imake this work?
No, the programming code is unique to the manufacturer of the universal remote. It is possible with 'learning' remotes to get the infrared patterns from the original by 'beaming' the codes from the old one to the new one.
In programming a ds converter using an RCA universal remote, it is necessary to find the code for the remote. This can be done by turning devices on and pressing search. It will rotate through and stop when the successful setting has been reached. Switch to each additional device that needs to be… connected on the remote and perform the same function. This will program all devices to work off the universal remote. ( Full Answer )
There are many codes available for an RCA tv. The main codes that work are 805, 627, 725, 503, 003, 641, 630, 830, 619, and 742. The related link below will allow you get additional codes if needed!
I got "006" to work for Channel Up/Down and Volume Up/Down. Still searching for a code to get me to the menu to change input/source.
The RCA universal remote code for a magnavox converter is 1563 if your remote serial number begins with RCU704.
The system and device is OK now. Imalent EU06 3 in 1 touch screenLED flashlight with remote control.
I have a 55 inch lg flat screen tv i need codes for a universalguide plus remote
740,350,442 if these do not work I'm sorry to all of you for your time
Turn the device on you want to program - the TV for instance. Point the remote directly at the TV. Hold down the TV button and the power button illuminates while also holding down the TV button at the same time. When the power button turns off, then release both keys. Now, point the remote directly …at the front panel of the device, hold down the play button for 5 seconds. Did your device turn off? If yes press the stop key and you're done. If no, keep pressing play every 5 seconds until your device turns off. When your device turns off, press the reverse key on the remote and wait at least 2 seconds. The remote tries the last of the previous ten codes. Hopefully this answer solves your problem. ( Full Answer )
The Sharp TV remote codes for a RCA universal remote are either 01 or 02. The exact code will sometimes depend upon the exact model of a person's TV.