0
Good question. I asked their customer service and they told me to use a nail. No amount of banging and bending nailes has come close to dislodging the pin. Arghh!
THIS WORKS: Heat the hinge with your hair dryer to loose the goop inside the hinge. Use pliers to hold the hinge as it will get very hot. Once it's hot enough, insert a small screw driver into the pin hole. Bang the screwdriver and I promise the hinge will come out. It worked for me on all my Schlage hinge pins.
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
How can you remove the pins from a hinge on a door inside your house?
You shut the door, if needed spray each hinge with WD 40. Then take a straight screwdriver and a hammer to pound out the hinge. In an upward motion the end of the screwdriver against the bottom edge of the top of the pin, then take the hammer and pound on the end of the screwdriver to loosen. When loose you may be able to remove it with your hand or pliers. The above will not work on some door hinges such as Schlage. THIS WORKS ON SCHLAGE: Heat the hinge with your hair dryer to loosen the goop inside the hinge. Use pliers to hold the hinge as it will get very hot. Once it's hot enough, insert a small screw driver into the pin hole. Bang the screwdriver and I promise the hinge will come out. It worked for me on all my Schlage hinge pins.
What is the same key as SC1 key?
Schlage 5 pin. Also Schlage C.
How do you remove welded on door hinges 02 Avalanche?
Buy a hinge pin and bushing kit then rebuild the hinge on the vehicle and avoid trying to remove the hinge off the vehicle.
How do you remove 1997 Mercury Cougar door pin hinge?
With your mouth.
How to remove 1991 camaro door hinge pin?
Open the door, support it with a jack, remove the hinge spring. To remove the pin, you should have to remove a retaining clip at the head of the pin and then tap it out with a hammer. The upper hinge has two bolt secured bushings. Unthread the bolts, tap them out with a hammer and pull out the bushings. Make sure the door is held secure, as it will be free floating at this point.
1994 jeep Cherokee how do you remove the door hinge pin i only need to replace the hinge half for the door the A piller half is okay.?
Hello... I have the very same problem. To remove the hinge pin, you must heat the center of the hinge where the pin goes through, and use an air hammer with a flat pointed end. Manage the air hammer under the hinge, point on the bottom of the pin and pull the trigger. Steady the air hammer so it doesn't move around on you. ....Good Luck!!!!
1994 jeep Cherokee how do you remove the door hinge pin i only need to replace the hinge half for the door the A piller half is okay?
Hello... I have the very same problem. To remove the hinge pin, you must heat the center of the hinge where the pin goes through, and use an air hammer with a flat pointed end. Manage the air hammer under the hinge, point on the bottom of the pin and pull the trigger. Steady the air hammer so it doesn't move around on you. ....Good Luck!!!!
What is the name for pin that slides into a door hinge?
door hinge pin
How do you remove hinge pin in the side door?
you have to lift the door up and use a hammer to hit it
How do you replace door hinge pins on a 1993 Mercury Cougar?
Hold the end of the door with a jack, grind the head from the old pin, knock out the old pin, remove the door half of the hinge, drill out the hinge to accept the new bushings, install the new bushings, re-bolt the hinge to the door, finally, insert the new pin and install the C clip
How do you change door pins and bushings on a 1999 Chevy blazer?
REMOVAL & INSTALLATIONSee Figures 1 and 2 Fig. 1: A spring compressor tool must be used to remove the springs when working on the doors/hingesFig. 2: Exploded view of the door hinge pinsThe following procedure requires the use of a door hinge spring compressor such as J-36604-A or equivalent. # If equipped with power door components, perform the following procedures: ## Disconnect the negative battery cable. ## Check for access to the wiring by removing the cowl side vent cover. If access is possible, remove the receptacles from the wiring harness, then remove the retainer from the wiring harness grommet. Remove the rubber conduit from the door pillar by pushing it from the vent cover side. ## If access is not possible, remove the door trim panel, then unplug the electrical harness connector from the power door lock motor and/or the power window regulator. Remove the harness from the door. # If available, apply cloth-backed tape to the door and body pillar for protection. CAUTIONBefore removing the hinge spring from the door, cover the spring with a towel to prevent the spring from flying and possibly causing personal injury.# Using a door hinge spring compressor such as No. J-36604-A or equivalent, compress the door hinge spring and remove it. # To remove the door hinge pin clips, spread the clips and move them above the recess on the pin; when the pin is removed, the clip will ride on the pin and fall free of it. ## Using a soft-head hammer and a pair of locking pliers, remove the lower pin from the door hinge; then, temporarily install a bolt (in the lower pin hole) to hold the door in place until the upper hinge pin is removed. ## Remove the upper door hinge pin and support the door, then remove the bolt from the lower hinge pin hole and remove the door from the vehicle. To install:# To install the door, position it on the hinges and insert a bolt through the lower hinge pin hole. # Using a new hinge pin clip, install the upper hinge pin. # Remove the bolt from the lower hinge pin hole. Using a new hinge pin, install it into the lower hinge pin holes. # Compress the door hinge spring and install it into the door hinge using the door hinge spring compressor tool. # If equipped with power door components, re-engage the wiring and install the trim panel or pieces, then connect the negative battery cable. ADJUSTMENTSFactory installed hinges are welded in place, so no adjustment of the system is necessary or recommended. Service replacement hinges are bolted in position and may be adjusted. If your vehicle is equipped with service replacement hinges, please refer to the door hinge adjustment procedure located later in this section. Depending on the type of door hinge you have, you wont have the clips mentioned above. If this is the case there will be a silver cap that sit on the top of the door pin. all you have to do it hit the top of the pin with a BF hammer (or rubber hammer) and a punch. The pin will come straight out. One thing to be aware of, as soon as that pin is out it will put all the pressure on the other pin. U should use a bucket and place it under the door so that it doesnt fall too much. I did mine yesterday and it took about 30 minutes. If you have the right tool (which I didnt) and someone to help you it should be no longer than 30 minutes. Good Luck!!!!!!
How do you replace a door hinge pin in a 1997 grand marquis?
To replace the door hinge pins on a 1997 Jimmy you will need to open the door up. Place two jack stands on the front and back of the door's length at the bottom portion of the door for support. Remove the damaged hinge pin with the proper socket. Place the new hinge pin in place and secure it.
