answersLogoWhite

0


Best Answer

1. Remove the screw holding the door-open handle bezel, and remove the bezel. Unhook the power door lock switch (if equipped) and set the bezel aside.

2. Carefully remove the power window switch from it's bezzel. There are 4 small clips, 2 on each side of the switch. Once you remove the switch from the bezel, the bezzel can be gently pried out the top of the panel w/ a small screw driver from the front.

3. Starting at the front w/ a small screw driver, pry out (gently!) the trim inlay that's above the arm rest... it was wood-grained plastic on this model.

4. Use a #30 torq bit to remove the large screw towards the top of the opening where the trim inlay was.

5. Remove the 4 Philips head screws around the perimeter of the door panel.

6. Lift up on the door panel... you may have to shake it a bit.... and after moving upwards no more that an inch... the panel should come off.

User Avatar

Wiki User

12y ago
This answer is:
User Avatar
More answers
User Avatar

Wiki User

12y ago

You will need a Phillips head screw driver, 10mm socket depending on yr., a plastic pry bar, and a flat head screw driver. 1st open door compltely. Take off the door lock position indicator with pry bar. take off power window and lock controls. Behind door handle there is a panel remove with pry bar. under this panel is a screw remove it. at the very bottom of door there is 1-3 screws remover them. check for any other screws. Starting at the lowest part of door closest to jam insert pry bar behind door facia. work your way around till door has completely released. lift from bottom till window seal is free then sit door facia on a towel or blanket to prevent scratching.

This answer is:
User Avatar

User Avatar

Wiki User

13y ago

First you have to unscrew the door handle bezels and remove them from the door panel. Then unbolt the door pull from the door of the car.

Next you have to pry the door panel tabs off of the door.

This answer is:
User Avatar

User Avatar

Wiki User

12y ago

there is little panel you must remove in the pocket under the door handle, there are two 7mm screws you have to take out. then take out the little plastic Phillips head screw behind the door handle. you have to pop out the little squar push pin the Phillips head screw was just in, use a pic tool. hears the tricky part, the plastic panels in these trucks break very easy so take your time but be firm when doing this, use a panel popper if you have one, go along the rim of the plastic molding hat surrounds the door handle, watch that you don't rip the leather or fabric around the piece, you have to pop that piece out so it will slide through the opening when you get the door panel off. remove the two trim pieces that run along the window, then start at one end of the panel and work your way to the other pulling on the panel until it pops free at each point. unplug the harnesses inside the panel and your done.

This answer is:
User Avatar

User Avatar

Wiki User

12y ago

To remove the rear door panel in your Chevy HHR, you will need to remove the two screws located inside of the door pull cup, and there's also one in the middle of the inside door handle.

On the outer edge of the door there's also a pin the holds the panel in place, you will need to remove that. Then use a door panel removal tool to pry the door panel off of the HHR rear door.

An instructional video has also been enclosed below that shows this entire process and where everything's located.

Hope this helps,

1ATony

This answer is:
User Avatar

User Avatar

Wiki User

9y ago

Use a screwdriver to remove all screws and clips in the door panel, and gently pull the panel away from the frame. Remove any wiring connections, and the panel will come off of the frame.

This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: How do you remove a door panel in a 95 jimmy?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

How do you replace the mirrors on a 95 gmc jimmy?

remove your door panel remove the rubbers grommets, remove 3 10mm nuts unplug if power, reverse process


How do you remove a jetta car door paneling?

Depending on the year, but i have a 95 and there are screws going around the outside ov the door panel remove those


How do you remove a 95 Honda accord LX sedan driver door panel?

To remove the door panel from a 1995 Honda Accord LX sedan the mounting hardware must be unscrewed. Afterwards the mounting clips can be pulled off along with the door panel.


How do you replace a door handle on a 95 Toyota tercel?

You will need to remove the door panel of your 1995 Toyota. Remove the door handle linkage. Remove the door handle retaining bolts. Reverse the process to install the new door handle.


How do you remove the door panel from a 95 ford escort wagon?

Removing a door panel from a 1995 Ford Escort wagon is very simple to do. The clips that are holding the door panel in place need to be removed, then the screws in the door will need to be taken off. After the clips and screws are removed, the door panel can be lifted off.


Where is the door light switch in a 95 Ranger?

it is inside the door panel


How do you install exterior door handles on a 95 jeep wrangler?

They can be removed and replaced from inside, you need to remove the inside door panel to get access, then its a few clips on the sides.


How do you get the door panel off of a 95 Chrysler LeBaron?

Pull off the speaker grille and remove speaker, ease out the seat/window/mirror/switch panel by sliding a screwdriver under the back end and ease panel out, disconnect wires from panel, unscrew escutcheon behind inner door handle, lift our small section of "carpet" from door pull and remove screw, locate and remove 3 screws in the bottom carpeted section of the door panel (you can feel the holes by running your fingers over the carpeted section) pull door panel away from door and disconnect puddle light and you are done!


How do you get to the front speakers of a 95 Isuzu Rodeo in order to replace them?

If the inside of a 95 is the same as a 97 the plastic grill on the door panel covering the speaker should pop off using a flat end screw driver. If theres not then you'll have to remove the door panel, which isn't hard. It can be done in about 5 minutes.


How do you remove and replace the driver's door mirror on a '95 Chrysler Cirrus?

Like most cars, you will probably have to remove the door panel, and there should be a few nuts holding it in place. the poor panel will most likely pop off, rather than just fall off when all screw are removed.


How do you remove the front door panel on a 95' Accord to access the speaker?

First you remove two screws that are located in the handle well in which you open the door and then you remove one that is located in the well which you usually close the door with. There is a third screw-like thing on the part of the door that is hidden when it is closed. Remove that with a flat head screwdriver. There are around 10 or so clips that hold the panel to the door. Find a good grasp and just pull and hear the poop off. The last thing is to lift the panel up. But the handle section and window swtich section have connectors on the inside of the panel that need to be disconnected. After doing so, fiddle with the panel a bit until it comes off.


How do you remove the door panel to replace the speaker in 1994 Saturn SL1?

on my 95 SL1 the plastic screen over the speaker just pops off with a screwdriver. dont take the door apart if you don't have to.