0
Be sure to deactivate the air bag before working on the steering wheel. I just disconnect both battery connections and let it set 15 minutes. Insert a flat tip screwdriver into each slot on the back of the steering wheel and twist slightly to release air bag retaining clips.Don't do this while sitting in the drivers seat, the bag might go off! Pull the bag off, release the small assurance clip then the connector will pull out of the air bag. Set it in the bed, bag side up so the cover can't become a projectile if it goes off. Pull the horn connector out of the steering wheel. Back the large bolt out most of the way on the steering wheel puller . Bolt the puller to the wheel with 2 bolts and screw the large bolt back into the puller. I tap on the wheel as I screw it in.
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
How do you remove air bag from 1999 Chevy silverado to get to horn switch?
Disconnect battery (very important!!!) There are bolts/screws that hold air bag to steering wheel. They screw into rear of steering wheel. Just unbolt, remove and disconnect electric conector.
How do you compress the steering wheel spring on a 1999 Buick Regal?
There is a special tool that pushes down the horn plate then remove the "C" clip,then a wheel puller to remove the wheel.
How do you remove 1999 holden commadore drivers airbag steering wheel?
To remove the driver's steering wheel airbag on a 1999 Holden Commodore you will need a special set of tools to remove the 4 to 6 security screws that are holding it in. If the vehicle came equipped with a airbag, it needs to have one to remain road safe.
How do you remove the steering wheel on a 1999 Windstar?
DISCONNECT BATTERY FIRST. Let set for about 20 minutes or so. This is to make sure no residual power left in system. Next remove air bag. Usually two screws holding it in from the back of the steering wheel. Remove the connector. There is probably a large nut. Remove the nut. Then you should be able to use some type of bolt puller or steering wheel puller to remove it.
How do you remove the spider gears in a 1999 chevrolette silverado?
how do you remove the spider gears in a 1999 chevy siverado?
How do you remove the clock spring located on a 1999 Ford Taurus SE?
Center the steering wheel with the wheels straight ahead. Remove the steering column trim, remove the ignition lock cylinder, remove the streering wheel. The clockspring is located under the streering wheel, and includes the ignition key-in warning pigtail. You will have to follow the wiring to the base of the column and unplug the connectors. Instalation is in the reverse order as disassembly.
How do you change a wheel bearing on a 1999 Mercury Cougar?
Remove the tire and wheel from your 1999 Mercury Cougar. Remove the axle end. Remove the wheel bearing retaining nuts. Remove the wheel seal and the wheel bearing. Reverse the process to install your new wheel bearing.
How do you replace the horn switch on a 1999 Chevy s10 pickup?
How do i remove the steering wheel cover to get at the horn contacts on a 1999 chev s10 You will be messing with the air bag and I recommend having a knowledgeable mechanic help you with this one.
Front wheel bearing hub nut on a 1999 Chevy Silverado 4x4?
36mm
Where is fuse box in 1999 catera?
under the dash below the steering wheel. u will need a flat head screw driver to remove a couple of screws.
Where is the fuse box on a 1999 e350?
Below and to the left of the steering wheel , by the brake pedal Remove the panel cover to access the fuses ( according to the owners manual )
How do you take out 1999-s 10pick-up steering wheel?
DISCONNECT BATTERY FIRST ! This way it makes safe the airbag so it wont hurt you if it goes off. There are screws behind the wheel you unscrew to remove the centre airbag assembly and expose the large nut that secures the wheel to the steering shaft. Remove it then you will need a steering wheel puller, (a tool you can rent from some auto parts houses and can certainly buy for around $50) to remove the wheel. Dont try and beat the wheel with a hammer, you will certainly damage the wheel and also run the risk of accidently smashing plastic dash or steering column parts, and as the wheel has been on since new, it wont come off without a puller.
