Firstly, remove the battery before you open the laptop case. The keyboard securing strip doesn't have any securing screws and shouldn't cause any problem when you remove it.
Secondly, unlock the metal plate before you pull the keyboard cable from the connector. The keyboard cable connector on the system board is cover by a metal plate and the plate has to be removed before you can get an access to the connector. To open the connector, move the connector lock toward the LCD screen. It is enough to move it 2-3mm to open the connector. Be careful with the keyboard connector on the system board. If you damage it, the entire system board has to be replaced.
You can remove the original keyboard and search for the part number which should be somewhere on the sticker and after that Google the part number.
Also, you can search on Sunvalleyus for "Toshiba keyboard" and buy it from there.
there is a glossy piece of plastic right above the keyboard it runs above the f keys .. just take a precision flat head screw driver and pop it up . there is two screws one on the right and one on the left under the plastic bar you just removed . unscrew them and lift up the keyboard. then there is a black connector with white heads . pull the white heads up and the keyboard should be free
Individual keys can be replaced if necessary, by purchasing keys from the manufacturer. You can also purchase an external keyboard that plugs into your USB port.
viruses were found on my toshiba laptop how do i get rid of them
Make sure you have no power going to the laptop, remove the power adapter and battery before starting. You'll need a Phillips screw driver, to remove the old keyboard. Unplug the old keyboard and plug the new one in making sure the groves match up. screw the keyboard screws and you are done.
You can access the hard drive from the bottom of the laptop. If you turn the laptop upside down, you'll find the hard drive door under the Toshiba sticker with the laptop serial number. Remove two screws from the hard drive cover and then remove the cover. Slide the hard drive to the right and remove it. Transfer the hard drive bracket to a new hard drive.
Try turning it on via the BIOS. if a password is there find a battery in the laptop and remove it.
It is very simple to change the keyboard on this model. The Acer 5720z is a fairly good laptop having a good life. First: Remove Battery Remove the 3 M2.5x4 screws as this will allow you to remove the top cover at the rear of the keyboard allowing you easy access to the keyboard. Be careful when prying off the cover as to much pressure will break the plastic. Once the rear cover is removed, remove the keyboard and pull out the ribbon cable attaching the keyboard to the motherboard. Install the keyboard and put it back together.
Removed the 6 screws from inside the battery area. Remove one screw in center bottom of laptop. Remove keyboard bezel CAREFULLY! Remove the 3 screws holding keyboard. Release ribbon cable connected keyboard to the motherboard.
A number of possibilities here: Have you tried in all USB ports? Have you tried the drive in another computer? I know on my Toshiba Laptop, if I plug the flash drive in B4 I power up, it doesn't read it, but if I remove the drive and then plug it back in it works (while machine is running)
Here are the simply steps you should follow to Remove LCD screen from Toshiba Laptop: 1. Remove two LCD mask seals. Remove two screws hidden under seals.2. Put your fingers between the mask and the LCD screen and carefully release the mask latches.3. Remove the mask. Do not hurry; twist the mask slightly to release latches.4. Remove the mask screw seals on each side of the display assembly. Remove screws.5. Remove the securing tape from the display connector. Disconnect the display cable. Remove the screw securing the FL inverter.6. Lift off the FL inverter board. Disconnect FL inverter cables on both ends.
Step 1: Establish if you need a new replacement screenStep 2: Find and remove the bezel screwsStep 3: Remove the bezelStep 4: Find the right replacement parts.Step 5: Replace the broken screenStep 6: Power it upPlease, follow the link to get more installation instructions.brief process :Level of difficulty: IntermediateThe laptop is a personal computer. Many individuals use laptops because of it mobility. It has a built-in display screen, keyboard, and a touch pad. Laptop also uses Wi-Fi for Internet connection, but it can also connect to the Internet by using cable. The most fragile and important part of the laptop is its display screen. You need to replace the display screen if there is a big damage on your laptop screen.Materials Needed:- A replacement screen- a flat head screw driver- a Phillips head screw driver- a small container or cup- anti static strap (optional).Step 1First, you need to use your anti-static strap or touch a metal to disperse any static electricity that you may have if you do not own an anti-static strap. Then, turn the laptop over and get your small containers for the screws.Step 2You will need to remove the battery of the laptop. Then, remove all the screw on the side of the screen and also remove the screws under the battery. You will also need to remove the keyboard and disconnect the wireless antenna wires. Be sure that you remember the place where you removed the antenna wires.Step 3After you remove the battery, you need to press and hold the power switch for about half a minute. Do this to disperse all the remaining power in the capacitors. The next thing to do is take the speaker bezel off using the flat head screw driver. Then, remove the plastic clips and be sure that you do not damage anything to ensure that everything will work afterwards.Step 4Remove the connected cables on the screen. You need to remove the video cable. Then, carefully remove the thin wires controlling the webcam and microphones of the monitor. Now that the screen is out of the way, you can remove the keyboard.Step 5Pull the screws on the keyboard using the Phillips screw driver. After that, you must gently remove the keyboard then detach the cable connecting the laptop and the keyboard. You must be sure that the cable will get no damage because if it does, the laptop might not work. After seeing the inside of the laptop, remember the location of the wires because you will need to get it back later.Step 6After removing the wires connecting the laptop and the screen, you can get the replacement screen. Then, attach the wires of the screen to the laptop and place the wires where it should be. Also, reattach the microphones, webcam, and video wires back. Put back the speaker bezel and reattach the keyboard. After that, turn the laptop over and then start putting back the screws.
To replace the keyboard for a Sony Vaio VPCEB, you will need to power down your laptop. Disconnect it from external power and remove the battery. Turn the laptop upside down onto a flat surface. The bottom vents should be facing you. There are two screws in the bottom center, one on each side of a removable vent plate. Remove these two screws. Set them aside in a small dish, or somewhere else they won't be lost. Turn the laptop right side up, open it, and carefully pull on the frame surrounding the keyboard. Start over the function keys and work your way around. The keyboard and frame are one piece, and they are held in place by plastic clips. You need to get to the keyboard connectors, so gently rest the keyboard on its face. Unlock the keyboard connector from the motherboard. There is a brown clip that you will need to move towards you. The cable will slide out of the connector. That's it. The old keyboard is removed. To install the new keyboard, follow through this same process in reverse. Plug the new keyboard into the motherboard, lock it in with the brown clip, and keep going.
As long as it is made for a laptop i dont see why i couldn't work. make sure you have a free ram slot or remove one so you can put it in though.
Each laptop allow to remove its keyboard, go through the manual how to, remove the keyboard. Usually each key can be removed too, make sure that you know how to... Remove each key and clean with clean water, dry it before installation. Clean the keyboard body with slightly wet tissue, dry before installation.