SETTING THE TIME AND DATE ON AN OLD 4 BUTTON DIGITAL WATCH
[L1]_____[R1]
| | | |
|____|
[L2] [R2]
SETTING THE TIME.
Press [L2] to move through the modes. When the time display flashes, you are in the correct mode to set the time. The hours first, then the minutes and seconds.
Press [R1] to advance the numbers, [R2] to go to the next.
Press [L2] to save your settings. [L1] is not used; it's the light.
SETTING THE DATE AND DAY. After setting the time (seconds flashing) push [R2] to move though time, backwards, to date, [R1] to set day, [R2] to move to month [R1] to set the month. Push [R2] to get to the day of the week, then [R1] to change. [L2] to end.
Try holding each button first.
When seconds start flashing, hit a different button to switch to minutes, then hours.
If that doesn't work try pressing two buttons simultaneously
You might have to be in a certain mode in order for this to work.
Some watches also let you set the time when you put in the battery.
If that doesn't work, your best bet is to look up the watch model and Google it, or better, go to the manufacturers website for a manual.
depends on the watch.
Something that works in every digital device with fleeting memory: Take out the battery.
Very simple Just press the SET button for 4 to 5 sec and it will blink the Sec continuously Now you are in setting mode and press the MODE button to select the time and date mode one by one and use the ADJUST button to set the correct time and date. Once you are finish the job press again the SET button to complete the same Cheers
It's actually pretty simple! There should be 4 buttons on your digital watch otherwise it may not work: Mode, Light, Start/Stop, Set. 1st. Click SET 2nd. Click both SET & MODE If it doesn't work that instant, try clicking both SET & MODE a few more times. And it should work the other way around, to change your digital watch from 12 hour to 24 hour.
If it's the one like I have, there are 4 buttons on the outer portion of the face. The bottom Right button controls the digital time. Compress and hold, the seconds feature should blink...press the top right button to change time. You can fast forward the setting if you hold down that top right button. To get to minutes, hour, day and month just keep pressing the bottom right button, and alternately press the top right button to change the quantity of seconds, minutes, hours, etc. Hope this helps. I was looking for an answer to this and just figured it out myself. :)
You go to it and hold the X button
1 Press and Hold the RESET button until screen flashes 2 Press MODE button until segment you wish to change is flashing 3 Press START/STOP button to change segment 4 Press RESET to exit programming mode
You can legally rent or purchase digital versions from iTunes or Amazon Unboxed.
1. press mode untill you are at the "section" (AKA alarm,time,stopwatch....) that you would like to change or set. 2. hold down the "set" button until the minutes/hours/seconds start to flash. 3. press "mode" to change what flashes (AKA minuts, hours,seconds.) 4. once you have got what you want to change flashing, press the adj. (adjust) button to change the number. 5. set your time! (remember to make sure that the number is "am" or "pm" , if you dont know how to tell, there will be a little "a" or "p" next to the hour...) 6. to finish setting your time, press the "set" button, this will exit the setting mode! have fun with your watch!
On an Echo 2003-2005 set time by: Press the button "4" then the seek toggle button. Then hold Am button and press "1" to increment the hours. Then AM and the "2" button for the minutes. release and clock is set.
Left 'trip button' is actually the clock set stick just below your speedo the button/stick to the right is the right trip button.
To set the time 1. Hold the reset button until the hour mode (12/24) is flashing 2. Press the mode button to scroll (year, month, day, hour) 3. Use the ST/STP button to advance 4. Press reset button to return to normal operation To set the alarm 1. Press the mode button to scroll to AL1 mode 2. Press the reset button to scroll through the 3 alarm modes 3. When alarm mode is displayed hold the reset button until the time is flashing 4. Use the ST/STP button to advance 5. Press reset button to return to normal operation Note: To change AM to PM you must advance through a complete 12 hour cycle.