0
I have a 49cc Hyosung scooter. Under the bike in front of the muffler there are colored wires. The Hyosung bike has an all BLUE wire -- It needs to be cut. Once cut, my bike got an extra 10-15 mph (top speed now 45 vs. 30)!!!!. I was in Martha's Vinyard and went to a scooter rental place that had my particular scooter. The expert there showed me how to do it. VERY EASY and EFFECTIVE.
Once the blue wire is cut you need to add a little bit of 2-stroke oil to each tank of gas due to the higher rev speed.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
How fast can a scooter?
Hos fast can a scooter... go? Scooter top speeds range depending on their engine size, gearing, bike weight, rider weight, etc. So details aside, the average answer would be from about 30 to 55mph, give or take (assuming engine sizes from 50cc - 150cc).
How do you increase speed on 50cc scooter 4 stroke engine?
Take out the top speed restrictor plate. If you don't know how to do it contact a proffesional. where are the restrictor plates located
Where is the governor plate on a Roketa 50cc scooter?
not for sure but with some scooters they restrict them with the muffler you may be able to take the muffler off drill out the inlet side of the muffler to allow more air flow
Take off governor from a kymco scooter?
how do you take the governor off of a kymco agility 50 scooter? There may not be a governor as such, it may be that the engine has been detuned or otherwise modified to limit its power or top speed. It may well be a violation of your state's laws to attempt to override any of this. Most states treat these scooters as mopeds, and the common limitation is max size 50cc, max power 2hp, and max speed 30 mph. A scooter that exceeds any one of these is considered a motorcycle and must be licensed and insured as such. But it may be that the VIN on the scooter can not be registered or insured as a motorcycle, so effectively, it is a violation of law to modify it. Make sure you understand your state's laws before you proceed.
How fast does an aprilla 50cc scooter go with no modefications brand new from a shop?
about 10 mph 50cc is cheap and slow get 110 cc or height then take it to a shop and tune it up
How do you find and remove the governor on a 150cc scooter?
all you have to do is take it off, how hard can it be.
What is the law for a 50cc motor scooter in Ohio?
you have to be 14 it has to be 50cc after 16 it can be whatever cc u want u must wear a helmet with a chin starp and u have to take 3 types of tests
Do you need a license to drive a scooter in GA?
If the scooter is 50cc or less you do not need a motor cycle license, insurance, or a tag but you still need at least an ordinary drivers license to take it on the road.
How do you take off your governor on a schwinn sport 50 scooter2008?
If you are having problems with the engine, take the scooter in for repairs. Since it is a late model, I would think it is still under warranty. If you are wanting to remove the governor to get higher rpm's and more speed, DON'T DO IT. The governor plays an important part in maintaining the engine at optimum performance by governing maximum speed. If you remove the governor, you will be risking serious damage to the engine due to uncontrolled overspeeding.
How old do you have to be to get a moped license in Tennessee?
You have to have a valid driver's license in order to operate a moped on public roadways in Tennessee. If you have a valid Tennessee driver's license, you will not need to take a test to get an endorsement on your license if you are operating a scooter or moped that has a top speed of less than 30mph and an engine size of 50cc or smaller. If the engine size is larger than 50cc, you will have to take the necessary steps to acquire a motorcycle endorsement on your license.
How do you take off the governor on a 49cc scooter?
should be where your throtle on your carb. its a screw with a spring.
How do you take the governor off a Kymco 50 cc scooter?
Removing the governor off a Kymco 50 cc scooter varies based on the type of restrictor it has. Mechanical restrictors require complete removal of the governor while electrical units simply need to be rewired.
