answersLogoWhite

0


Best Answer

Explain what you mean by "3-way outlet". I've heard of 3-way switches, but not 3-way outlets. I would guess the person asking the question is asking how to wire a three-prong socket, as opposed to a four-prong socket...

User Avatar

Wiki User

17y ago
This answer is:
User Avatar
More answers
User Avatar

Wiki User

14y ago
Answer for USA, Canada and countries using similar 60Hz household electricity supplies
If the socket outlet or plug-point is part of the house wiring and is 4-prong (4-wire is the proper term) then you MUST purchase a 4-wire cord and plug for the appliance and change it out. Most home stores (Lowes, Home Depot) sell these cord and plug sets just for that reason.

How to install the new cordTo upgrade your appliance, go to the hardware store and buy a new 4-prong 110/220V cord with a ground that is the right size in amperage for the appliance. 30A for dryers, 50A for ranges. Remove the old cord, and install the new cord. If the old cord was flat without a color code, the two outside wires are the hots (red and black on the new cord) and the center wire is neutral (white on the new cord). If the neutral lug is bonded to the chassis, break the bond. The green wire in the new cord grounds the chassis. Connect the green wire to a convenient screw in the chassis, if a dedicated green ground screw is not provided.

Before you do any work yourself,
on electrical circuits, equipment or appliances,
always use a test meter to ensure the circuit is, in fact, de-energized

IF YOU ARE NOT REALLY SURE YOU CAN DO THIS JOB
SAFELY AND COMPETENTLY
REFER THIS WORK TO QUALIFIED PROFESSIONALS.

This answer is:
User Avatar

User Avatar

Wiki User

14y ago

== == == == (LIFE SAFETY WARNING! [disclaimer]

Electricity is dangerous!

You can be injured or killed!

Improper installations can cause fire, injury and death!

Should you be doing this yourself?)

This is one of those questions - if you know this little, you shouldn't be doing what you are planning...

No disrespect intended, but this is SO basic that it suggests you have not studied the subject at all!

There are many good reference books and course books to study from.

<><><>

This is one of the most commonly asked questions in FAQ forums about electricity and wiring.

It must be understood that new appliances will be designed to meet the newest standards.

It is not reasonable to expect someone to rewire their home because they need a new dryer or range [stove]!

According to the NEC [National Electrical Code], it is now required to isolate the neutral conductor from the appliance frame or chassis.

It used to be allowable to use the neutral as a grounding means by incorporating a

link between the neutral and the chassis.

The problem with this is that, should the neutral become "open" at some point, the chassis or frame then becomes energized!

The answer to this safety issue was to require a separate grounding conductor in the cable feeding the appliance.

The NEC allows the replacement of the new four prong cord with a three prong cord for appliance replacements in existing installations only!

It is then required, when the cord is thusly replaced, to establish the frame grounding link from the chassis to the neutral.

<><><> Turn off the power! Disconnect grounding strap (or green wire) from chassis of dryer that leads to the common on the wire block on the back of the dryer. Then wire as follows: Red and black wires to their respective hot terminals on block on dryer.

White to common lug on block of dryer. Green to grounding strap or wire that is connected to the chassis of dryer (no longer attached to common on the wiring block.

ALWAYS CHECK WITH YOUR LOCAL WIRING SAFETY OFFICE BEFORE YOU ATTEMPT TO CHANGE ANYTHING

- BREAKERS, CABLES OR OUTLETS -

ON ANY ELECTRICAL POWER CIRCUITS

IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOB

SAFELY AND COMPETENTLY

REFER THIS WORK TO QUALIFIED PROFESSIONALS.

If you do this work yourself, always turn off the power

at the breaker box/fuse panel BEFORE you attempt to do any work

AND

always use an electricians test meter having metal-tipped probes

(not a simple proximity voltage indicator)

to insure the circuit is, in fact, de-energized.

This answer is:
User Avatar

User Avatar

Wiki User

11y ago
for USA, Canada and countries using similar 60Hz household electricity power service By asking this question you are probably not quite ready to take on this particular task.

You may or may not get lucky and receive some information in an answer here!

If you hope to get enough information on this site to be able to do this job properly and safely, please do not rely on getting accurate information about such a potentially dangerous subject.

Really, don't do this one yourself. Electricity is far too dangerous to handle if you have not been trained how to do this work. If you put just one wire in the wrong place you risk being killed by electrocution or you could even start a house fire.

How to do this job depends entirely on the Wiring Codes or Regulations for the locality (Town/State) and on the exact location of the outlet you wish to use. If it is anywhere that is subject to water splashes or spray - such as in any room supplied with running water pipes, like a kitchen, bathroom, shower room, etc., or in a pool-side area - in many places nowadays - including New York City - it is actually illegal to attempt to do this kind of work unless you are already a licensed electrician.

If you don't want to go to your local library or bookstore - to find and read some books about electrical wiring and appliances and how to install them safely, and to find out about your local Wiring Codes and Regulations - then the best advice anyone should give to you is to call a licensed electrician either to do the job for you or to advise you what you may be allowed to do yourself.

Note

Nowadays the voltages supplied to homes are nominally 120 volts and 240 volts + or - 10%. The actual variation from nominal at any instant in time will depend partly on the distance you are from the power station and partly on the overall load being drawn by the population using the same power service.

However many people still call their home voltages "110" volts and "220" volts and it really doesn't matter because the actual voltage you get could vary from 132 V down to 108 V in the case of the nominal 120 V, and from 264 V down to 216 V in the case of the nominal 240 V.

IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOB

SAFELY AND COMPETENTLY

REFER THIS WORK TO QUALIFIED PROFESSIONALS.

If you do this work yourself, always turn off the power

at the breaker box/fuse panel BEFORE you attempt to do any work AND

always use an electrician's test meter having metal-tipped probes

(not a simple proximity voltage indicator)

to insure the circuit is, in fact, de-energized.

This answer is:
User Avatar

User Avatar

Wiki User

14y ago

Not sure exactly what you're trying to hook up but to give you an example - if you have an electric dryer with a 3 prong cord and want to use a 4 prong receptacle, you would really have to change the cord to a 4 prong. In a 3 wire cord situation, the neutral and ground are bonded together. You have to separate the neutral and ground in the dryer itself.

This answer is:
User Avatar

User Avatar

Wiki User

13y ago

Can you combine the black and red wire and connect it to the black wire from the house and have standard 110V service? Just take a little longer to cook?

This answer is:
User Avatar

User Avatar

Wiki User

11y ago

Click the link.

This answer is:
User Avatar

User Avatar

Wiki User

13y ago

You dont.

This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: How do you connect a 240V appliance with 3 wires to a circuit with 4 wires?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

How do you connect a European 240V appliance 3 wire plug with black and blue and green wires to a US 240V circuit?

European wiring has two principal colour schemes: On appliances from the last 40 years, and recent fixed wiring: Live: Brown; Neutral: Blue; Earth: Green with yellow tracer On older appliances, and in older fixed wiring: Live: Red; Neutral: Black; Earth: Green OR Green with yellow tracer. Until you can satisfy yourself (beyond any doubt) as to which wires on your appliance relate to live, neutral and earth, you should NOT attempt to connect the appliance. Either check the manual or contact the manufacturer. Also, depending on the appliance, you need to consider that the US uses 60Hz alternating current whereas Europe uses 50Hz. This may or may not prevent the appliance working correctly.


You have 277 supply is it safe to connect 240v appliance?

I believe the rule of thumb is 10% either way and you have exceeded that.


How can you convert US 120V or 240V circuit into a single phase 240V circuit to use on a European appliance?

The voltage isn't a problem, you can run 220 from your house and use that to run a European appliance, the problem is whether the appliance is dependant on line HZ. European is 50HZ and US is 60HZ. If the appliance specifies 220/50HZ, it will probably give you trouble here. If it says 220V/50 or 60HZ


Can a kitchen stove be on the small appliance circuit?

No, unless it's a gas range. An electric range requires 240V and 40A while a small appliance will be 120V and Max 15A.


What happens if you plug a 120V appliance into a 240V outlet?

You will burn up your appliance!!!!!


How do you connect a relay in single phase 240V ac circuit?

To answer this type of question more information is needed. Click the discussion tab.


Originally a 240V line running from the 50A circuit to a box contaning in line fuses from this box came a 240V cable having 2 black wires and wire braid do I wire the outlet stove as a 3 or 4 prong?

3 prong the 2 black wires are your hot and the braided is your neutral.


If you have a spa that is 240V with 4 wires can you hook an extension cord from a 240V welder to it to see if it works if the cord only has three wires?

Well, maybe. What is the current rating on the spa circuit? What is the current rating on the welder? If the welder is larger than the outlet, then no. It must be the other way around. If the current ratings are OK, then yes. Your welder doesn't need 110V so it doesn't connext to neutral. Connect the hot leads to hot and ground to ground.


How do you upgrade the service from a 120V 100A circuit breaker to 240V 30A for appliances like ovens and dryers?

Have an electrician wire you a proper line for the appliance. You were just kidding about the 100A, right? 10, or 20amp, not 100.


Would saudi 220v 60hz appliance work on malaysia 240v 50hz?

yes.


Where can you buy a 220 circuit breaker here in US?

at your local hardware store go to the electrical dept, not the normal but the contractors area and you should find a 240v circuit breakers, fuses, junctions, wires and anything else you can think of!TucsonDirect


Does a 10amp 240v appliance draw 5 amps per phase?

Answer for USA, Canada and countries running a 60 Hz supply service.No. Even though 240 volts uses two breakers it is still classed as a single phase service. Kirchhoff's law states that current entering a circuit is equal to current leaving the circuit. Since the appliance draws 10 amps, the whole circuit has 10 amps flowing through it.