answersLogoWhite

0


Best Answer

I put an aftermarket one on mine a while back but this is only good for 93-98...if yours is newer it may be different. If i remember right to take it off you have to open the rear hatch and take off that plastic strip on the top part of the bumper that should just pop up with a screwdriver...maybe a screw or two. Then go around the rest of the plastic part of the bumper looking where it is held on which again should be nothing but plastic clips that will pull off. Once that is off you can get to the metal underneath that should just be a few bolts holding it on. I cant really remember how the rest came off...some help i am. I've never put one back on but if you dont break the clips it should just pop back on.

The removal process is made very easy by purchasing an inexpensive door panel removal tool. Use this tool to remove the plastic snap rivets from the bottom and top of the bumper cover and inside wheel well coverings as needed. A 10mm deep socket is used to remove two nuts on the inside of each rear fender. Use a torx head driver to remove the fasteners just inside the left and right side of the tailgate. Once these fasteners are removed, carefully pull the rear corner panels away from the body. They are held in place by two plastic horizontal V clips so a popping noise is normal. The bumper cover is now free to be pulled off

The 10mm screws are accessed by removing the rear of the inner fender well covers held in place by two plastic push pins.

User Avatar

Wiki User

8y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: How does one remove and install the rear bumper of a Jeep Grand Cherokee Laredo?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

How to remove the radiator on a 2001 jeep grand Cherokee Laredo with air cond?

First remove the front clip (headlights and grille and plastic covering the bumper.) The rest will be obvious.


How do you remove the trasmission oil pan in a 1991 Jeep Cherokee Laredo?

I need to know asap how to remove a trasmission oil pan on a 1991 jeep Cherokee Laredo? Thank you!


Where is the blower motor in your 96 jeep grand Cherokee Laredo?

I mean how do you disassemble the fan blower in a 1998 Jeep Grand Cherokee Laredo. how do you remove the blower fan from the car in the Grand Jeep Cherokee Laredo.


Replace water pump on 94 Jeep Grand Cherokee Laredo?

Remove the water hose and allow the water to drain into a bucket. Remove the retaining bolts. Reverse the process to install the new water pump.


How do you install 2004 Acura tsx front bumper to a 2004 Acura tsx?

You remove the clips on the top, screws by the fenders, remove foglights if equiped and remove the bumper, install the new one in the opposite order.


How do you remove the front bumper on a 1994 jeep Cherokee 4 door?

behind the bumper, there are 4 bolts , 2 on each side.


Remove heater core 1993 jeep grand Cherokee Laredo?

Do you live in an area that you need your heater?


Do you need to remove the intake manifold when replacing the exhaust manifold on jeep Cherokee Laredo 4.0?

Yes.


Can you get to the fuel pump in a 2001 Jeep Grand Cherokee Laredo from the inside of the truck?

No, you will need to remove the tank.


How do you install jeep power steering pump 2000 Jeep Cherokee Laredo?

Remove air filter assembly. Loosen Belt, place pan under steering box, disconnect high pressure and return hoses. Remove bracket to engine bolts, remove pivot bolt, remove bracket and pump as one whole unit. Then reverse the process to install.


How does one remove a front bumper from a 1997 Jeep Grand Cherokee?

First remove the bumper cover. You need to take off the front grill to get at the plastic retainers that hold the top of the buimber on. There are about four retainers on the bootom of the bumper.


Where is the radiator fan relay on a 2001 Jeep Grand Cherokee?

On my 2000 grand cherokee, It was in front of the battery on the fender wall. Remove battery and you should find it. It is under the bumper cover, under the passenger head light. You either have to remove the front bumper, or you remove the headlight and cut an access hole.