0
It depends on what yours using it for. I use 12 ish
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
Does Voltage have anything to do with the clients skin for a tattoo?
If the voltage is fit, it will have no harm to your clients skin. Make sure you are using the high quality of tattoo power supply.
How do you decide the speed of the tattoo machine?
Each artist finds and performs different settings for their personal machine, allowing the artist to feel comfortable using the machine. The type of skin the client has, along with the size or type of tattoo, determines the setting of the machine and the power supply. Plug in the power supply and attach the cord to the tattoo machine. Place the tube in the tattoo machine and insert the needle in the tube. Tap the foot pedal to ensure the machine is working. Adjust the springs on the tattoo machine to control the depth. Apply pressure with the hand that holds the machine, pressing down into the skin for more depth after adjusting the springs. Turn the voltage of the power supply up to adjust the speed. The more voltage, or higher setting, of the power supply equals a quicker speed. A lower speed is optimal for tattooing bony areas of the body and high speeds for fleshy parts.
How expensive is it to build a high voltage power supply?
There are many guides on the internet for building a high voltage power supply. The average cost for building one of these power supplies is around $20.
For what are high voltage power supplies typically used for?
High voltage power supplies have many uses. It is most commonly used to supply power from a device to the circuit. These are great for people who need to supply their house with power.
Do high-spec desktops need a special power supply?
A good power supply plays a fundamental part in the stability and reliability of desktop computers. Corsair, Seasonic and Antec each manufacture high quality power supplies.
What power do you set your tattoo machine?
The tattoo power supply should be set under 3V for machine. some useful parameter: Tattoo machine: 3-15V, Starting 3V,working under 6-9V. Tattoo power supply: input AC:110V-220V conversion, output DC: 0-15V conversion, starting work under 3V.
Why should you not wear an antistatic wrist strap to repair power supply?
The problem here is that you may encounter high voltages in the power supply. So wearing an antistatic wrist strap may put you at a greater risk of electric shock. Besides, there are few if any sensitive electronic components inside the power supply unit.In addition, make sure the power supply is not connected to any power before servicing it. If you need to go near any large capacitors, you will want to discharge them. In fact that is a good precaution to take any time you remove the circuit board from the power supply unit.
What effect does a power spike have on a computer?
A power spike - also known as a power surge - could harm a computer if the computer's power supply has a low joule (unit of energy) rating. A power spike, a sudden increase in energy, can overwhelm a computer's power supply and cause too much electricity to flow to sensitive chips and processors and destroy them. To safeguard against power spikes a surge protector should be bought. A computer power supply with a high joule resistance rating would work as well.
Advantages of using electrolytic capacitors?
the have large capacitance value, power rating is high , and its constriction. To smooth power supply ripples.The output of a sinewave with the bottom waves cut off is a power supply without smoothing.You would get a hum in an amplifier if it wasn't smoothed by a large capacitance,say 400 Microfarads.On a 12volt supply as in a portable tv,the power supply smoother is around 2000 microfarads.The output waveform should be nearly a straight horizontal line with no ripples on it.
If the power supply has blown what are chances that it has taken out the motherboard or something else?
Very unlikely. When a power supply "blows", a fuse is destroyed in the power supply. This is what the fuse was designed for. When a high voltage comes through, the fuse will burn out to prevent the surge from reaching the rest of the electronics. A surge protector does the same thing, but is better at catching voltage spikes than the power supply.
When is the IS curve steep?
relatively low supply of high power money (monetary base low)
What are the typical ratings for a computers power supply?
300Watts for low end and 950Watts for high end
