General rule is 24 hours but read the bucket.
Grout is a material used to fill voids in concrete or tile structure. Grouting or Injection Grouting or Pressure Grouting invariably means the process of injecting grout into isolated pores or voids in a concrete or tile structure.Eg:- Injection grouting in a concrete water storage tank.
I am currently working on this problem myself, having waited too long to clean tiles after grouting. We are using steel wool pads and spackle implements to scrape off the excess grout. I thought it might damage the tile but it really has not. It's a tough job, good luck. I am currently working on this problem myself, having waited too long to clean tiles after grouting. We are using steel wool pads and spackle implements to scrape off the excess grout. I thought it might damage the tile but it really has not. It's a tough job, good luck. Also a mild solution of sulfumic acid will remove most cement products... available at home depot .
No, porcelain tile needs to be grouted which seals the floor. The tiles have their own water resistant finish on them when purchased.
You can drill through tile, but doing so would most likely crack and break the entire tile. It is not recommended to drill through a tile, unless it is a soft tile, where the tile will not break if drilled through.
wall tiles are used on walls. floor tiles are used on floors. if you want to interchange. you can make the wall tile as floor tile and vice-versa
The general rule is to wait 18 to 24 hours before walking on or grouting.
Grout is a material used to fill voids in concrete or tile structure. Grouting or Injection Grouting or Pressure Grouting invariably means the process of injecting grout into isolated pores or voids in a concrete or tile structure.Eg:- Injection grouting in a concrete water storage tank.
Improper tile grouting will allow water to ingress to the surface of whatever the tile is laid on to ie plaster wall , concrete backer board , this will in time lead to the tiles becoming loose and damaging decoration in adjoining rooms
What is composition of cement and any other metrial for grouting on floor ceramic tiles.
Allow to cure for 24 hours before grouting or light traffic, depending upon temperature and humidity. Polyblend® Tile Grout is recommended.
So long as the grouting is done correctly a tiled pool is much easier to keep clean and looking uniform. other then that there isn't that much difference.
Do you need to seal ceramic tiles? (Natural eg slate or stone, you definitely would). Anyway, I'm no expert on this, but from researching it on the web, it seems that if you seal first, and then make a mistake with the grouting, you can clean up very easily. If you don't seal first then it's a much tougher job to clean up.
You must make the measurements that you need to lay the tile, then lay out the tiles on the floor to help familiarize yourself with the pattern you are going to be working with. Lay your grouting adhesive and then finally the tiles.
Yes you can. First are there any cracks in the floor? If so you need to put down an anti fracture membrane otherwise the new tile will just crack again. Second use a better quality thinset, one made for difficult bonding like Stonewall or REflex by Hydroment. If you scratch up the old tile a little it cant hurt. Also it will take more time for the thinset to dry and cure because the moisture has less places to go, the old tile or membrane acts like a raincoat so stay off the tile for at least 24 hours, 48 would be better before grouting. stickandgo.com now produce a self adhesive wall tile that looks like a ceramic tile and it does not need cementing or grouting and can be applied over existing tiles without getting them off the wall ! I know that Stick and Go do over 50 ranges from their website.
I am currently working on this problem myself, having waited too long to clean tiles after grouting. We are using steel wool pads and spackle implements to scrape off the excess grout. I thought it might damage the tile but it really has not. It's a tough job, good luck. I am currently working on this problem myself, having waited too long to clean tiles after grouting. We are using steel wool pads and spackle implements to scrape off the excess grout. I thought it might damage the tile but it really has not. It's a tough job, good luck. Also a mild solution of sulfumic acid will remove most cement products... available at home depot .
It depends on the type of tile you have. If the tile is unglazed and porous (as mostly all travertine is) then you will need to seal the tile before you grout it so that the grout does not soak into the tile and cause it to become dull. Follow the manufacturers recommendation for the tile that you have.
It depends on the type of tile you have. If the tile is unglazed and porous (as mostly all travertine is) then you will need to seal the tile before you grout it so that the grout does not soak into the tile and cause it to become dull. Follow the manufacturers recommendation for the tile that you have.