i believe its a 4 inch. i just recently bought a 74 f250
Factory lift kit installed VIE factory were truck is manufactured
Skyjacker makes a 2 and 4 inch lift using new leaf springs. Summit racing and jets sells them. Since the highboy is lifted 4 inches from factory this will give you 4 additional inches incorperate a 3 inch body liift and gain 7 inches should clear 40 inch tires easy.
The F-250 4wd Highboy for 1976 & the first couple of months of 77 had factory lift and hydrolic slave cylinder steering in addition a Dana 44 front axle with Dana 60 Knockles, known as 44-6cf .
Answer'66 marked the first year of the Highboy in the F250 line. They ran up to '77.5 in which midway thru the year Ford changed the 3/4 ton line and went to the "Lowboy". VIN numbers determine whether a '77 is that or the '77.5 year. The Lowboys after 1977.5 will have married transfercases which are bolted right behind the transmission via an adaptor. Front driveshafts are shorter and rears are longer. also came with hi-pinion diffs, Leaf springs are flatter than the Highboys and frame bends are different, too.'66 began the Highboy and it ran clear up to '77. I know I mentioned '66 where the '67 began the body change. The '66 is the old body before the '67 started.The aftermarket line of suspension lifts is available for the Highboy from Skyjacker. They offer 2" and 4" lifts, both with front springs and the rear, narrow springs available in 4" only.Highboys have 3" wide front springs and 2.25" wide rear springs. Lowboys after 1977.5 have 3" wide front and rear springs.Where a 4" Skyjacker front spring lifts a Highboy that much, it will lift a Lowboy 6". The Highboy has a difference of 2" of raised height than the Lowboy. Rear factory blocks in Lowboys are 3" and Highboys are 4". These springs don't lift the highboy an additional 4" they are basically replacment springs. I know I have them on my truck.There are some confusing ideas on what makes a truck a highboy or not. first of all the term highboy was first coined by the owners of the trucks according to a Ford partsman I know, he said that ford made, nor assigned no name or title to these trucks, what makes a highboy is that the truck is assembled using different springs etc... to change the ride height, I don't know if this applies to the '66 thru '72 trucks, so here goes, I have had two(2) ford trucks 1976 & 1974, both F250 4wd both had divorced transfer cases. one of them sat approx. 4" higher that the other. Also When ordering parts for the trucks I noticed that there was a split in the VIN numbers for a lot of the parts. Trucks with VIN's before #Y20001 sat higher than the trucks after #Y20001, now this is just an observation of mine. While my trucks were both stock, the 1974 sat lower and had front springs that were almost flat and had no blocks in the rear. while the 1976 had front springs that were arched quite a bit(4") and the back suspension had blocks with a bump stop arm cast in them they measured (4.25") high.If anyone has a better explanation please share it 67-72 were set up the same way, however all the high boys used a 3 1/2 inch block, have had several, including a 75 and a 76. And yes the skyjacker 4 in does add 4inches over the high boy setup do to maintaining the rear block. I have the same lift and went with the full spring set up.. this set up on a high boy gives u about the same as a Chevy with a 8 inch lift . So the front springs r not just a replacement..they r
Take a tape measure and measure from the center of the hub to the closest part of the fender. Then subtract 1". They will vary for that old of truck depending upon spring sag. It is probably about a 35".
leveling kits
The factory lift pump on a 6.6 Duramax is located in the fuel tank.
the 3000 is factory rated to lift 1700 pounds.
in the trunk passenger side. lift the black cover to the indentation an you will see the factory amp.
West Germany in 1974.
They replace the factory body mounting bolts.
AS Saint-Etienne won the 1974 Coupe de France. They defeated AS Monaco to lift the trophy.