The furnace that is working properly should cycle on and off after every 3 - 4 hours.
turn breaker off. unhook thermostat wire to furnace turn breaker on. worth a try; if it works you will have to turn off breaker to shut it down.
Well, I don't mean to sound snarky, but when it doesn't work anymore! The thermostat, in its most basic form, is just a switch to turn the heater on. If the heater turns on and off like it should, it is OK. If the heater doesn't turn on, or worse yet doesn't turn off, you should look into getting a new one. Some tests you can perform: Heater doesn't turn on? Get at the wires running to the thermostat and touch the two control wires (You will have to look into the furnace documentation if you have more than two wires) together. If the furnace clicks on, it's the thermostat. If it doesn't, it's the furnace. Heater doesn't turn off? When the furnace is running disconnect one of the control wires. If the furnace shuts off it's the thermostat. If it doesn't, it's the furnace.
Well, I don't mean to sound snarky, but when it doesn't work anymore! The thermostat, in its most basic form, is just a switch to turn the heater on. If the heater turns on and off like it should, it is OK. If the heater doesn't turn on, or worse yet doesn't turn off, you should look into getting a new one. Some tests you can perform: Heater doesn't turn on? Get at the wires running to the thermostat and touch the two control wires (You will have to look into the furnace documentation if you have more than two wires) together. If the furnace clicks on, it's the thermostat. If it doesn't, it's the furnace. Heater doesn't turn off? When the furnace is running disconnect one of the control wires. If the furnace shuts off it's the thermostat. If it doesn't, it's the furnace.
i have a model 125u19 payne furnace i move the thermostat but nothing comes on in the furnace and the pilot light is lit
It's when you turn on the heat you loon
No it is not advisable. Put it on AUTO. The furnace will decide when it is practical to turn the fan on. Really. No it is not advisable. Put it on AUTO. The furnace will decide when it is practical to turn the fan on. Really.
Just search water cycle poems on safari and it should turn up a good amount of poems
Carbon will not escape with the furnace off and it will only choke you because you will be breathing it carbon not oxygen. So my advice is dont turn the furnace off
I have a Frontier Campervan conversion on this vehicle type and can answer for that. 1) Turn on the propane at the tank. 2) Take the front panel off the furnace by pulling the top straight out then lifting. 3) Turn the propane on at the furnace by rotating the red knob 1/2 turn to the ON position. 4) Replace the furnace cover. 5) The wall thermostat has an ON/OFF switch on the bottom. Click it to the ON (right) position. 6) Adjust the temperature using the top slider on the thermostat. The thermostat should first start the blower then, after a few seconds, start the igniter. I can easily hear the igniter 'tick' as it sparks. That's all there should be to it.
An A/C unit is not required to run a furnace. You will want to make sure there are no gaps or missing equipment.
Turn the thermometer switch to offTurn the electrical service switch by the furnace to offTurn off the main breakerAfter turning off the main breaker disconnect the power line to the furnace
It could be different for every house.A side note: I'm taking that you mean where is the pilot light located in side your furnace? Depending on the of your furnace it's very possible your furnace does not have a pilot light, in fact it may have an ignition system with a flame management sensor. Try this; turn off the system with the main electrical cutoff switch, wait for about 2 minuets, turn on the switch raise the temperature of the thermostat high enough for the furnace to come on, this should work if it does not try one more time. If that fails call a HVAC & R technician.