How do you get the laser dragon in Dragon City?

Answer 1

Step 1

You will need the following items:

1. 16X DVD Burner. I used an LG burner I had as a spare.

2. A Mini-Mag Flashlight

3. An AixiZ Laser Module.

4. Small jewelers screwdrivers, X-Acto knife, metal snips, drill, round file and other small tools.

step 2

After removing all of the screws from the DVD burner, remove the cover and the DVD drawer. This will expose the laser carriage assembly.

step 3 Extract the Laser Diode..While all DVD burners are a bit different, they all rely on 2 rails that the laser assembly moves on. Remove all screws and do whatever it takes to free up the rails so the laser assembly slides off. Disconnect or cut and cabling and flat connectors. step 4 Continue extraction...Once you have the assembly off of the burner it's time to start disassembling it by removing all the screws you see. There will be many small screws so be patient. Cut any flat cabling off. There could be two diodes, one for the CD portion of the burner (IR diode) and the actual DVD burning diode (red). That is the one you want. There will be a 3-pin circuit board on the red diode that you want to CAREFULLY remove with a soldering iron revealing 3 pins. You can test the diode with 2-AA batteries and referring to the polarity chart (on the video). You will have to remove the diode from the housing and that will be in a case-by-case basis depending on the burner. The laser diode is fragile so take care in the final extraction process. step 5 Preparing the AixiZ housing...Remove the label from the AixiZ housing and unscrew the housing leaving a top and bottom portion of the housing. Inside the top housing is the original (5mw) laser diode that has to be removed. I used the bottom of an X-Acto knife and with a couple of sharp taps, the original diode will come out. It will likely be destroyed doing this but I have been successful in removing them before but using a very small screwdriver and tapping around the diode until it is freed up. step 6 Assembling the housing...I used a little bit of Arctic Silver Thermal grease and slowly installed the new DVD diode in the AixiZ housing. Using a pair of pliers, I SLOWLY squeezed the edges of the diode down into the housing until it was flush. CAREFUL! step 6 Installing it in your MiniMag!After soldering two leads to the positive and negative diode connectors, it's time to install it in the MiniMag. After disassembling the MiniMag (remove the top, the reflector, lens and bulb) you will need to enlarge the MiniMag reflector using a reaming tool, round metal file or drill or a combination of all three. step 7 Final Step!!Be sure to remove the batteries from the MiniMag and after checking polarity, slip your new DVD Laser housing down into the top of the MiniMag where the bulb would go. Screw the top of the MiniMag on and slip the reflector over the Laser housing. You will not be using the plastic MiniMag lens. And now your done!

Answer 2

Laser (Light Amplification by Simulated Emission of Radiation), is generated by a light emitting laser medium (lasing material) and optics to manage the light emitted from the lasing material. The lasing material can be charged electrically or optically so that the atoms or molecules in the lasing material have high energy states. Light is emitted when a high energy atom or molecule changes to a lower energy state. As the emitted light hits other high-energy atoms, more light is emitted. The generated light will have the same wavelength (color), phase angle and direction as the incoming light. As a result, light is amplified in the charged lasing material. Arranging optics, such as two parallel mirrors, to bounce the generated light back into the lasing material, can create more light that moves in the same direction.

Answer 3

You have to get the goggles from the lady stuck in the cage. You can open the cage by pushing the cherrybomb up to the cage and wait for it 2 explode. then she will give you clue#3 and the goggles.

Answer 4

to buy a laser and dismantle it and remake it and it will be stronger as soon as you put a glass inside it really works!

Answer 5

you hide behind the statues

Answer 6

breed fire dragon with electric dragon