answersLogoWhite

0


Best Answer

Unless you're VERY mechanically inclined, I suggest you leave your machine in the hands of a shop that works on snow throwers and small engines.

That being said, I replaced my auger cable this afternoon. It took almost two hours. If I knew what I was doing, I probably could have done it in 30-45 minutes. The part alone was $29.99.

Consider the snow thrower as two separate pieces bolted together. On the one end is the engine and the controls. The other end is the auger and thrower. On my machine (Toro 824, circa 1997), there are three bolts on each side of the machine holding thw two sections together. As luck would have it, I took out the top two on each side, and the snow thrower cracked open Ike an egg, still attached by the lower bolts. Then I had to take out two more bolts that held the spring-loaded pulleysin place. This was necessary so that I could get at the part where the spring at the end of my auger cable acually attaches. (I forgot to mention a two plastic covers {top and bottom} that need to be removed first.) You should probably remove the control that roates the chute before you crack the transmission open.)

It would have helped considerably if I had a helper, but alas, I was solo for this mission.

When you set the lock nuts on the handle end of the cable, I used (what I thought was) common sense, and set the cable so that with the handle depressed, the cable was pulled just a little bit more than the amount needed to move the pulley to the extent of its travel. The extra pull would be handled by the spring at the cable end.

Would I tackle this task again? On my machine, sure. On a friend's machine, only if I owed him/her a HUGE favor.

Good Luck.

I only searched online for this answer just to see if I could have done it easier and simpler.

User Avatar

Wiki User

12y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: How to replace auger cable for snow blower?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

How do you replace the auger cable on a MTD snow blower?

To replace the auger cable on the MTD snow blower, you have to disconnect it from power. Use a screw driver to open the screw and replace the auger cable in question.


How do you replace an auger cable on craftsman snow blower?

Replace Angus cable craftsman 3.8 snowblower


How do you replace the auger belt on your snow devil snow thrower?

how to change belt on snow devil snow blower


Where is the auger belt on snow king snow blower?

It is under the cover between the blower and the motor.


Difference between a single stage and two stage snowblower?

A two stage snow blower has the auger up front that moves the snow into the paddles that throws the snow. A single stage just has paddles, no auger.


How do you replace the drive cable on a Craftsman snow blower?

having trouble replacing drive cable the end of the cable is an "s" and the pulley is in the way so it is too tight to fit in whats the proper method


How many belts in a master craft snow blower?

the answer is two the larger belt is the drive belt and the smaller of the two is the auger belt.


You tried to install a new auger belt on a yardman snow blower without success any info on installation?

How to put new belt on


How much snow can an Ariens snow blower remove?

It depends on the model. Their smallest models are only capable of dealing with light snow, while the professional models have a 36 inch width and sport a 16 inch auger.


How do you replace gears on John Deere snow blower?

Its called a wrench and a lot of patience


How do you replace a friction wheel on a MTD snow blower?

http://www.youtube.com/results?search_query=mtd+snow&search_type=&aq=f


How do you replace the auger drive belt on a Toro 521 snowblower?

Got a toro 521 wont blow snow after 2 feet whats up