0
Answer for USA, Canada and countries running a 60 Hz supply service.
The first thing to do at the distribution panel is to turn off the breaker feeding the receptacle's circuit.
To the new two gang light switch box, two wires will go from the wall receptacle, connected black to black and white to white and ground to ground, to the new two gang light switch box and then two more sets of cable wires will leave the new light switch box and proceed up to the new individual light fixture boxes.
In the two gang switch box, first connect the incoming and outgoing ground wires to the ground screw in the new switch box.
Be sure to connect the ground wire around the grounding screw in the light fixture box.
Next the white wires will be spliced together with a wire nut and pushed to the back of the box and then the incoming "hot" wire will be connected across the top of the two new switches.
Pre position the switches in the off position, which is the handle down, before attaching the wires. The "hot" incoming wire connects to two pigtail wires coming from the top screw of the two switches. These three wires will be spliced together with a wire nut and pushed to the back of the new switch box.
The two black outgoing wires that feed the new light fixture boxes are connected to the bottom screws of the individual switches.
When either switch is turned to the on position, voltage will be applied to the appropriate fixture junction box.
As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.
Before you do any work yourself,
on electrical circuits, equipment or appliances
always use a test meter to ensure the circuit is, in fact, de-energized.
IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOB
SAFELY AND COMPETENTLY
REFER THIS WORK TO QUALIFIED PROFESSIONALS.
Wiki User
∙ 10y ago
Wiki User
∙ 14y agoThe short answer is to wire it the same way you would to operate 1 light. The second light is simply put "in parallel" with the first light.
Add your answer:
Earn +20 pts
Is there a way to wire a 3 way household dimmer switch as a 2 way dimmer switch?
You need a three way switch to control lights from two locations. The name is misleading. Three way switch refers to the connection points on the switch. You can use a three way switch as a single switch as long as you place hot wire on the brass screw and the use any of the other screws for the return hot.
Can a three way switch be changed to a single pole switch with a plate over one of the switch locations?
Yes, If you only hook up two wire it will work as a single pole
How do you hook up one light to one switch in a basement lighting system that has all 10 lights connected to one switch?
If you have good access to the wiring this is relatively easy to do. Each of the 10 lights is connected to another in parallel in a "daisy chain" fashion. Light 1 is connected to the switch, light 2 is connected to light 1, light 3 is connected to light 2 and so forth. Let's say it is light 5 that you wish to switch separately. You can first install the new switch by either adding a new box or modifying old switch box. There are two gang switches that will fit the form factor of a single switch. TURN OFF THE POWER TO SWITCH BOX. Using the same supply input at original switch, add a new black wire to the wire nut for input to original switch and connect this to the input of new switch. Then run a new wire to light 5 and connect black wire to the output of new switch. Connect all the white wires together in switch box and separately connect all bare wires together in switch box. Now at light 5 undo the black and white wire coming from the fixture, and reconnect the wire nuts so that there is a direct connection between light 4 and light 6. Do the same for the ground if present (bare wire). You now have the fixture wires hanging free. Now connect the black wire from new switch to the fixture black wire and white to white and you are done.
Can you use 14-2 wire to operate a ceiling fan using two switches one for the fan the other for the lights?
On these types of installations an electrician would use a three wire cable set from the switch box to the fixture's junction box. At the fixture's junction box both the fan neutral and the light neutral would be wire nutted together with the incoming neutral from the switch boxes. From the three wire, the white wire would go to the fan and light's neutral wires. The Black would come from the bottom of one of the switches and go to the fan's motor lead. The red wire would come from the bottom of the other switch and go to the light fixture's lead. It can be done with two runs of two wire to the fixture. You will need a two gang switch box for this project to hold the two separate switches. You could use a single gang light switch box if you can still find where duplex switches being sold. A duplex switch is one that has the configuration of a duplex receptacle with the switches being one on top of the other. The cover plate is the same one used for duplex receptacles. To answer this question fully more information is needed. See discuss in the left margin.
Why would there be power to ground wire instead of switch and lights Lights stopped working all of the sudden outside?
There will always be voltage to the ground wire, this is normal. The reason being is that the ground wire is bonded to the neutral terminal block back at the distribution panel. If you have a voltage reading to ground at the outside fixture with the switch in the on position then you have an open return neutral wire. This wire should be traced back from the light to the distribution panel. Check ever junction box that the circuit goes through and look for a loose or open white neutral wire. Closing the circuit where you find this fault will correct the problem.
You have three 3-way switches operating 3 ceiling lights you want each switch to operate each single light What do you do?
wire each switch to each light...
How do you wire running board lights on 2007 Toyota Tacoma?
run a wire from battery positive to an inline fuse, then to a switch that you have to install in your dash. from the switch to the lights, then to ground. turn on switch, lights should work.
What is difference between single pole and double pole switch?
A single pole switch interrupts only one wire, which must be the live wire. A double pole switch interrupts both the live and the neutral, so it contains two separate switches operated by the same lever. Current practice is to use single-pole switches, to avoid a fault condition which could leave equipment live while switched off.
Install daytime running lights on Nissan Frontier?
If you cut the wire from the light switch to the frount running lights (single use light) you can then hook a new wire from a keyed power source (check manuel) and the running lights will come on every time you start the truck. costs $Priceless
How does a double pole switch work?
A switch is inserted in series with a single wire. When the switch is on, it is as if the wire had not been opened to insert the switch. When the switch is off the wire is open and no current can flow. All a double pole switch does is allows you to switch two separate wires at the same time with the same switch action. A single pole switch just switches one wire.
Where does the neutral wire go on a single pole switch?
Unless the switch has a light to indicate the switch is turned on, there is no neutral connection to a single pole switch.
How do you wire a receptacle from two switches one is 3 way one is single pole?
You cannot wire a single pole switch and 3 way switch together.
What is wrong with a 1996 Honda Accord if the parking lights and dash lights are out but the fuses and bulbs are OK?
either the switch is not working or a wire to the switch is broken
Is there a way to wire a 3 way household dimmer switch as a 2 way dimmer switch?
You need a three way switch to control lights from two locations. The name is misleading. Three way switch refers to the connection points on the switch. You can use a three way switch as a single switch as long as you place hot wire on the brass screw and the use any of the other screws for the return hot.
How do you hook up fog lights on a 2006 freightliner Columbia?
Depends on how you want to go about it. If this vehicle came with fog lights, they're routed through the ECM, and that process requires you to have the corresponding software... if you're up for spending a few thousand on it, go for it. If you're trying to wire up fog lights in a vehicle which didn't originally have them, I would find an empty slot in the vehicle's fuse panels. From there, run a wire (I'd recommend at least 14 gauge, although 10 would probably be better) to a switch in the dashboard... you can either get a two pole, single throw switch, or, for about $5, you can get a single throw, three pole switch which lights up when engaged... the only difference is that you have to run a ground from the switch to get it to light up when engaged. The wire from the fuse will go to the switch input, the wire from the switch output will go to the fog lights. From the fog lights, you'll need to find a good ground to connect to the fog lights. Just as an aside, don't be one of these rookies who run their fog lights when there is no fog. Unless you're driving a 2005 or later Volvo VNL, the headlights are more than adequate.
How do you wire a cable with a black wire a brown wire grey wire and earth wire to a light switch in my car which has 3 holes 1 for single switch and 1 for a doubleswitch?
See discuss question below.
Where is the switch that activates the back-up lights on a 1996 Grand Cherokee?
It is a three wire switch on the driver side of the transmission.
