Open your bonnet, look to the extreme rigth around the arm that holds the bonnet open you should see the electrical fuse box. Directly in-front of this is a black plastic box,located inside is the fuel pump relay. Hold the plastic box cover and lift upwards it should expose the relay. This is true for some 190,s others have there fuel pump relays located on the opposite side of the engine compartment behind the plastic cover behind the battery.
In the Power Distribution Box ( which is " live " ) in the engine compartment : Relay # 48 is the fuel pump relay and mini fuse # 26 is a 20 amp fuse for the fuel pump Also , the fuel pump inertia switch is in the right front passenger footwell by the kick panel
On a 2002 Ford Explorer : In the Power Distribution Box ( which is " live " ) located in the engine compartment by the brake fluid reservoir ( # 48 is the fuel pump relay ) * also , mini fuse # 26 is a 15 amp fuse for the fuel pump
the fuel pump relay is located on the left shock tower in the engine compartment in a black box 6x4x1 inches. there are other relays inside the same box which is actually called the ccrm or constant contorl relay module, there should be a double connector with 20 to 26 wires in it, hard to miss.
In your power distribution box in your engine compartment fuse # 26 is a 15 amp mini-fuse for your fuel pump and relay # 48 is the fuel pump relay . What problem did you have in the first place that had you checking the fuses in the PD BOX ?
It is rated as 26 gallons but because the fuel pump is located inside the tank it actually will only deliver about 25 gallons.
This also happen to me on 8-26-07. While driving at 65mph the car lost all power & shut down, the car has 71K miles. A week ago I had to replace the hose that runs from where you pump gas into the car to the gas tank. Where is the fuel pump located on this year & model?
Relay - song - was created on 1972-05-26.
running 26-35 off 37-43 and it dont matter if its a dohc or ohv.the pressure is the same.
Relieve the pressure from the fuel system. Remove or disconnect the following:Negative battery cableRear seat and the access coverFuel pump electrical connectorFuel lines from the fuel pump assemblyLocking ringFuel gauge assemblyFuel tube and connector from the fuel gaugeNOTEWhen the fuel sending unit needs to be removed, pull the tab upwards. The tab is located on the sending unit, opposite the end of the float. After the tab is pulled, the sending unit will lift straight out of the tank bracketRelease the fuel pump by pinching the 2 locking tabs together. Lift the fuel pump assembly straight upward and out of fuel tank.Place a clean rag in the hole to keep out dirt.To install:Remove the ragNOTE When the fuel sending unit needs to be removed, pull the tab upwards. The tab is located on the sending unit, opposite the end of the float. After the tab is pulled, the sending unit will lift straight out of the tank bracketNOTE Verify that the mark on the fuel tank and the components are aligned when installing the pump and fuel gauge sending unit.Instal the following:New O-ring and fuel pumpElectrical connection and fuel tube to the fuel gauge sending unitFuel sending unit into the tankIf equipped with a threaded lock ring torque the ring to 22-26 ft. lbs. (30-35 Nm). If equipped with a lock ring held by six retaining screws, torque the screws to 18-22 inch lbs. (2-2.5 Nm). Fuel lines and fuel pump electrical connector. Always install new clamps on the fuel lines.Negative battery cableStart the engine, check for leaks and repair if necessary. Reinstall the fuel pump access cover and rear seat
Fuel tank holds 26 gallons.
The is none to check.Cam drive is by chain located under the valve cover and in the timing chest.
As per page 95 of the owners manual The electrode gap is 0.8 mm (0.032 in)