answersLogoWhite

0


Best Answer

If memory serves me right you need to remove the pan and remove some parts up front that won't allow the pump to come out until you do.

User Avatar

Wiki User

14y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: Is there a trick to removing the pump on a GM 700R4 transmission after removing the pump face bolts?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

What is the Trick for getting to and removing all the bolts on 93 ranger manual trans?

1. wheels-chalked for safety e-brake on. remove drive-shaft support tail shaft of transmission with hydraulic jack remove cross member supporting transmission lower back of transmission just enough to reach upper top bolts with long extension and socket NO trick just experience .


Is there a trick to removing the transmission from a 2000 Chevy S10 zr2?

After everything is unbolted use a pry bar and shake it from the rear tranny. there is also little bolts that bolt the dust plate to the engine block.


Is there a trick to removing the alternator bracket from a 1995 Jetta?

You should be able to remove the alternator bracket, on your 1995 Jetta, by removing the three retaining bolts. The bracket should easily come off.


Is there a trick to removing the charge cord from a Nintendo DS unit?

#


How do you change transmission fluid on 1996 Ford Thunderbird?

You have to remove the transmission pan. Jack the car up and then place jack stands under the car for safety. Then looking up at the transmission you will see the pan there are bolts holding the pan to the housing remove the bolts and the pan will drop off this will let about 4 quarts out there is also a filter in the valve body that has to be replaced. Be careful with the pan gasket it is reusable. This can get pretty messy when the pan drops so hold the pan and do not let it fall when removing. A trick I use is to take a electric oil pump used for removing oil on boat engines (cost $12.00 JC Whitney) and remove almost all the oil out through the fill tube that way when you drop the pan the remaining stays in pan and does not splatter all over you. when replacing the pan and gasket another trick is to get four (3 ) inch bolts cut the heads off screw one in each corner this way when you put the pan and gasket back on this will guide the pan an keep the gasket from moving. Hope this helps.


Is there a trick to removing a Yamaha Virago 1200 starter?

It's a real pain. I had to bend the head of a wrench to get at one of the 4 bolts holding it in. If you have the engine out, it's real easy. A lot of times the starter is the not the problem on these bikes. The starter bendix that is behind the clutch is the problem if you hear grinding when you try to use the starter.


Where is the PCV Valve on a 1989 Acura Legend?

It's on the front valve cover. The trick is you have to first remove the "breather chamber" by removing the 2 bolts on top. With the breather chamber cover off, you'll see the PCV valve screwed into the valve cover.


What is the trick to replacing a starter on a 94 Bravada?

What is the trick for removing the starter, from the engine, I have the starter unbolted but has a small compartment that stops me removing it from the engine?


What is the trick to changing out the starter on a 2000 Fiat Spider without removing the engine?

You need a long extension (3 feet) and a sloppy socket. This whill enable you ly on the ground just below the drivers side door and loosen the bolts/nuts. Hope this helps.


How to remove pinion yoke?

After removing the pinion nut, a 2 jaw puller should do the trick.


Does anyone have a good trick for getting the top bolt out of the transmission-to-engine on a 1999 4x4 S10?

Removing the distributor may give you the clearance you need from the top. I also go thru the bottom with a 36" 3/8" drive extension and a universal socket.


What is the trick on removing the main relay?

The main relay can be removed by removing the three main wires. The relay is secure with four retaining screws. Remove the retaining screws.