What would you like to do?
Answer I believe that it is on the passenger side of the center console, down by the floor. In the general area of where your left ankle would be, if you we…re sitting in the passenger seat. Answer I have a '94 Saturn SL2. There is the above mentioned fuse panel, but there is also another one under the hood, on the driver's side. It holds the larger fuses for things like your horn and headlights.
Answer almost all vehicles have one under the hood, and in your case also on the right side of the center console down by pass left foot. just pull off.
Answer There are two fuse boxes. If you are facing the radio, on the right side under the panel and also in the engine by the battery is another.
REMOVAL OF STEEL PANELS Begin by drilling out the spot welds along the door post, along the bottom edge forward of the wheel well, and at the seam where the Quarter Pa…nel meets the tailgate. Usually these welds are visible enough, but gentle lifting pressure under the folded edge with a screwdriver or chisel will make them impossible to miss. You needn't drill all the way through both layers; just enough to pop the weld is adequate. The rusted arc of the wheel well itself is usually pretty mangled, so just separate the inner from the outer as best you can. Tin snips are in order here, as are gloves to protect against sharp edges. We've found that the best place to cut along the top edge is approximately 1/2" down from the crease or shoulder which separates the flat top surface from the curved side skin. Cut as straight as possible along a line 1/2" down from that shoulder, all the way from the door post to the tailgate. Once the skin is removed, be sure to remove the entire outer piece of the wheel well itself -- again by drilling out the spot welds which join the two pieces. The replacement.
Answer Yes! If you use some plastic mesh. Just follow the directions.
Need more info. Are you trying to replace the clips that hold the door to the frame, or is the door delaminating. What kind of vehicle?
Saturns are just a little different than other automobiles. You don't remove the inside door panel to get to the mechanism, instead, you remove the outer door panel. Open th…e door. There are several screws around the perimeter of the door, some near the bottom. They must all be removed. From the outside, lift the handle and notice that there are two pins holding the door handle in place. They need to be pressed out, then you can pull the handle off the pegs. Once the screws and the handle are off, the outer door skin lifts off.
J B Weld or a similar epoxy.
use wood glue
Your Question is Incomplete Please ask your question again and include more information in it. WikiAnswers is designed to provide a specific answer to a specific question.Ques…tions that do not contain enough information cannot be answered - asking "did he die?" or "how did she become rich?" cannot be answered because we do not know who you are asking the question about.Multiple choice questions cannot be answered because you cannot include the choices in the question. These typically include the phrase "which of the following" at the beginning of the question and the questioner does not include "the following" choices in the question; thus, we have nothing to answer your question.General questions usually cannot be answered because it would take an entire website or a textbook to do that - questions such as "Explain biology" or "What are the names of all cars ever made?" are too broad to be answered.Questions that require us to look at a picture or diagram that you have in front of you cannot be answered because we cannot see your assignment page.Questions that must be answered with the questioner's opinion cannot be answered by anyone except you - job application questions such as "Why do you feel you should work for this company?" or "Where do you hope to be in five years?" cannot be answered by another person.Partial questions or question fragments cannot be answered - a sentence fragment such as "preparation for a position" or "pi plus" do not explain what your question is, and cannot be answered.Questions that are actually statements cannot be answered because they are not questions. "You are in love with a boy and he does not know you exist" is not a question and cannot be answered.Questions that should be asked in a chat room cannot be answered because this is not a chat room. "Who are you?" or "What is your favorite color?" are not questions that can be answered on this website.The WikiAnswers Style book will help you write a proper question that can be answered for you. See related links below.Tip: Don't use pronouns such as he, she, it, them, their, his, her, it's, and so forth in your question. Chances are, we won't know who she, he, them, and what it is and won't be able to answer your question. You must indicate the subject properly in your question. However, questions in which the subject is already indicated within it, may use those pronouns, ex: "When Miley Cyrus starred on Hannah Montana, how old was she?" is okay.Time Zone Questions with Insufficient InformationWhen asking about the time in different places around the world WikiAnswers can only answer if we know (1) the place of interest and (2) a reference point.Bad question that can not be answered: What time is it now in England?Good question: What time is it in England if it is 11 AM in Perth, Australia?Bad: What is the current Central Time?Good: If it is 2 PM in San Francisco then what time is it in Central Time?Bad: If it's midday in the US what time is it Japan? (What time zone in the US?)Good: If it's midday in Chicago what time is it in Japan?Bad: How many hours is Tonga behind?Good: How many hours is Tonga behind Tahiti?The differences are quite clear.It might make sense to YOU when asking but please note that it might be hours or days before someone looks at your question. In the examples above for bad questions, do you see how someone answering might be, well, a bit flippant and just say "8 PM", or "Evening", or even "Working time"? And that would not really help you out, now would it?Just for reference: Russia has 11 time zones; Asia has up to 8 (depending on how you count); the USA has 6; Australia has 6 (more or less, depending, some with, some without DST); South America and Africa have 4; Mexico has 4 (one of which does not observe DST); Europe and Greenland have 3; and the middle east has a whole fistful.Time zones between areas or countries may be as little as 15 minutes apart or as large as 120 minutes. Memphis Tenn. USA is NOT the same as Memphis, Egypt. Be specific -- Help us to help you!If you believe that your question has sufficient information to be answered and should not have been placed into this catch-all question, please e-mail WikiAnswers @ Answers.com and request that it be made into a separate question.
Would i tack weld a peice of quarter panel from another prelude of the same generation and then grind it down, sand, primer, and then paint it?
A hot glue gun works great for plastic parts. ANS 2 -Autobody shops use an epoxy called 'Speedgrip' -expensive, but excellent stuff. Available at auto supply stores.
The silver surface is there to reflect the heat back on to the solar panel. thats if any heat has gone through the solar panel
Not 100% sure here but i believe it is to reflect the sun back towards the panel to double the efficiency by making use of both sides of the panel.
by not using ur lights
Quarter panel in another name for fender, sometimes including the inner and out fender panels.
Easiest way to reassembling would be to call a technician from the manufacturer. He/She will do it for a fee, as disassembling a washing machine almost always voids its warran…ty. You could also consult the owner's manual of your washing machine. (However, Washing Machines usually do not come with an instruction manual for disassemble and reassembly ) Follow the instructions on reassembling.