0
Is there continuity from the center lead of the feed line to the antenna rod on a K30 CB antenna?
Wiki User
∙ 9y ago
There will be some amount of continuity in a k30. There is a coil at the bottom of the antenna base, so the ohm reading will be high, but should still be there.
Wiki User
∙ 9y ago
Add your answer:
Earn +20 pts
What goldfish grow big?
feed them lead feed them lead feed them lead
Why do they use lead in car batteries?
economical and the continuity of lead is very high
How do you change a vy commodore antenna?
The antenna feed is connected to a lead in the passenger footwell, so can be disconnected without removing the head unit. The antennat motor and assembly is accessed through the passenger wheel arch, after removing the wheel and plastic cover.
Why will my Ford radio will not pull out?
Did you disconnect the antenna lead?
How do you replace the radio in a 1999 Chevrolet Malibu?
remove center bezel and ignition lock cover and remove the 4 screws and unplug connectors and antenna lead in rear of radio
What do you need to hook up new tv to outdoor antenna?
You will need a tv antenna and a coaxial lead in wire with connectors.
How do you replace antenna on 1998 Honda Civic?
Honda Civic Car Stereo Antenna Removal and InstallationCar Stereo Repair Home | Car Stereo Removal | BOSE repair | FAQ | Shipping | Top 10 | About UsBroken antenna mast ! 1) Remove two screws securing antenna mast base to roof. 1) See car stereo removal instructions for removal of left dash panel.2) Disconnect antenna lead, located at edge of side panel by fuse block. This saves removing the entire stereo.3) Pull antenna cable free back to opening behind fuse block and trace up to opening. (Remember this spot!) 1) Pull old antenna and cable from top of car roof. Cut antenna lead and tape new lead to end.2) Feed new antenna mast into opening while pulling old antenna cable from inside car, (reach back behind fuse block for antenna cable and pull through opening and back to connector.)3) Push antenna mast completely to car body and tighten two screws.4) Be sure to lower antenna next time through car wash.
Whats wrong when plasma stays black but you can hear the sound?
the video feed isn't getting through (AV cable not inserted properly or faulty or incorrect cable being used). If the only cables going into the tv are the AC lead and the antenna cable the tv is faulty and needs a repairman the video feed isn't getting through (AV cable not inserted properly or faulty or incorrect cable being used). If the only cables going into the tv are the AC lead and the antenna cable the tv is faulty and needs a repairman
How do you check for a short in your car wiring?
You must check for continuity in the wiring. You will need a voltage/continuity tester. place one lead at one end of the wiring and place the other at the opposite end of the wiring. If the continuity tester does not indicate a constant flow of continuity it will NOT light up or "sound off."
How do you remove the stero from a 2005 mustang?
# Remove the center trim panel # Remove the radio mounting screws then pull the radio out of the instrument panel just far enough to access the electrical connectors and the antenna cable on the back of the unit # Disconnect the electrical connectors and the antenna lead from the backside of the radio and remove the radio
How you can inceares efficiency of antenna?
Height, direction, antenna type and down lead are major factors in receiving a good TV signal to the TV set.
How do you remove the power antenna on a Hyundai accent 1998?
Answer1998 MY (model year) Accent vehicle do not have a power antenna. Antenna mast should simply unscrew from mount.Step 1Activate the antenna switch to the up position.(turn on radio)Step 2 Using the wrench or needle-nose pliers, loosen and remove the original retaining nut on the base of the antenna mast.Step 3 Gain access to the underside of the area where the antenna is located.Step 4 Remove the bracket or brace that is below the hole and holding the antenna in place.Step 5 Remove the mast.Step 6 Find the motor that controls the antenna mast. Generally, power antennas will have a constant 12-volt lead and a ground lead. The ground lead will be grounded to the panel next to the motor.Step 7 Remove the ground lead from the panel.Step 8 Pull out the antenna coaxial cable.Step 9 Unplug the coaxial from the extension coaxial cable.Step 10 Remove the original antenna coaxial cable. Note the route the cable follows.Hope it helps
