1. Close all the vehicle doors, insert the ignition key in the vehicle's ignition.
2. Press and hold the door unlock switch.
4. While holding the door lock switch in the unlock position, cycle the ignition ON, OFF, ON, OFF, then back to ON and leave it in the ON position.
5. Release the door unlock switch. The door lock will activate to confirm the programming mode.
6. Press and hold both the LOCK button and UNLOCK buttons simultaneously on one remote transmitter. Press and hold both buttons at least 15 seconds.
7. Turn the ignition switch OFF, then to the ON position in order to exit the programming mode. Turn the ignition key to OFF and remove.
8. Operate the transmitter functions in order to verify correct Lock and Unlock button functions.
9. Repeat the previous steps to program up to 4 transmitters.
Unlock the car with the remote or the key in the door.Unlock the car with the remote or the key in the door.
How do I re-program a remote for a 1997 mazda millinea?
Unlock with the remote or with the key in the door cylinder.
Unlock the doors with the key, or use the remote.
To program your 1997 Chrysler Sebring remote, take your remote and key in the car with you and press the 'lock' button on the remote five times. Put the key in the ignition and turn it to the 'on' or 'run' position, then wait for the chimes to stop. Next, press the 'unlock' button on the remote and hold it down for four seconds. While holding the button down, press the 'panic' button at the same time and hold them both down for one second before releasing them. You'll hear another chime. Next, press the 'lock' and 'unlock' buttons at the same time and release them at the same time. Finally, press and release the 'unlock' button. When you hear the chime again, you're finished.
crowbar.
the dealer normally does this service for no charge
1997-2000 You can program up to 4 remotes on this vehicle 1. Turn the ignition ON 2. Within 4 seconds press LOCK or UNLOCK of first remote 3. Within 4 seconds turn the ignition OFF 4. Within 4 seconds turn the ignition ON 5. Repeat steps 2 thru 4 twice 6. Within 4 seconds press LOCK or UNLOCK of first remote 7. The doors will now automatically lock and unlock to let you know that the programming mode has begun 8. Within 15 seconds press LOCK or UNLOCK of the first remote which allows the doors to lock and unlock once and lets you know that the remote is now programmed 9. Press LOCK or UNLOCK of each remaining remote (if you have any) allowing the doors to lock and unlock once as each remote is programmed 10. Turn the ignition OFF 11. Remove the key You will have to program all old remotes because the transmitter memory was overwritten!! 1997-2000 You can program up to 4 remotes on this vehicle 1. Turn the ignition ON 2. Within 4 seconds press LOCK or UNLOCK of first remote 3. Within 4 seconds turn the ignition OFF 4. Within 4 seconds turn the ignition ON 5. Repeat steps 2 thru 4 twice 6. Within 4 seconds press LOCK or UNLOCK of first remote 7. The doors will now automatically lock and unlock to let you know that the programming mode has begun 8. Within 15 seconds press LOCK or UNLOCK of the first remote which allows the doors to lock and unlock once and lets you know that the remote is now programmed 9. Press LOCK or UNLOCK of each remaining remote (if you have any) allowing the doors to lock and unlock once as each remote is programmed 10. Turn the ignition OFF 11. Remove the key You will have to program all old remotes because the transmitter memory was overwritten!!
check in your owners manual if you have it.
To program the keyless entry remote you hold down the lock and unlock keys at the same time while within 10ft of vehicle to make sure you are within range of the remote for approx 10 seconds. the vehicle will alert with a short horn sound. if it does not respond, repeat. should only take 1-3 tries before it's done
The dealership scan tool is required.
Where is the thermostat on a 1997 chevy suburban and how do you change it?