Got this from the computer at the Dodge dealership diagrams wont show on here you can e mail me for the full doc with the pics at jaylatunski92392@Yahoo.com
TIMING BELT
REMOVAL
Raise vehicle and remove accessory drive belt splash shield Accessory Drive Belt Splash Shield

1 - ATTACHING SCREW
2 - ATTACHING SCREWS
3 - SPLASH SHIELD
Remove accessory drive belts. Refer to COOLING SYSTEM for procedure.
Remove crankshaft pulley and damper Timing Belt System

1 - ENGINE SUPPORT BRACKET
2 - TIMING BELT COVER (UPPER OUTER-B)
3 - TIMING BELT TENSIONER
4 - CAMSHAFT SPROCKET
5 - GENERATOR BRACKET
6 - SUPPORT-A
7 - SUPPORT-B
8 - BRACKET
9 - TIMING BELT COVER (INNER-A)
10 - TIMING BELT
11 - CRANKSHAFT SPROCKET
12 - FLANGE
13 - TIMING BELT COVER (UPPER OUTER-A)
14 - TIMING BELT COVER (FRONT LOWER)
15 - ACCESS COVER
16 - TORSIONAL DAMPER
17 - CRANKSHAFT PULLY (A)
18 - CRANKSHAFT PULLY (B)
Support engine and remove right side engine mount. Refer to procedure in this section.
Remove engine support bracket Timing Belt Covers

1 - BRACKET HARNESS CLIP
2 - REAR COVER D BOLTS
3 - COVER (REAR REFERENCE)
4 - BRACKET HARNESS CLIP
5 - UPPER FRONT COVER (OUTER)
6 - UPPER REAR COVER
7 - LOWER COVER
Remove timing belt covers Timing Belt Covers
Same as the pic above
Mark belt running direction for installation Timing Belt Engine Sprocket Timing

1 - TIMING MARK
2 - TIMING MARK (GENERATOR BRACKET)
3 - WATER PUMP PULLEY
4 - TIMING MARK
5 - TIMING MARK (TIMING BELT COVER INNER (A)
6 - MARK BELT
7 - CAMSHAFT SPROCKET (FRONT)
8 - TENSION SIDE
9 - TIMING MARK (OIL PUMP)
10 - TIMING MARK
11 - CRANKSHAFT SPROCKET
12 - TIMING BELT TENSIONER
13 - CAMSHAFT SPROCKET (REAR)
Loosen timing belt tensioner bolt Timing Belt Tensioner and remove timing belt.

1 - BELT TENSIONER
2 - TENSIONER SPRING
Remove crankshaft sprocket flange shield Timing Belt System
Same pic as step 3
CAMSHAFT SPROCKETS
You not gonna have the special tool so make your own lol
To remove camshaft sprockets:
Hold camshaft sprocket with Spanner Tool MB-990775. Loosen and remove bolt and washer Camshaft Sprockets
Remove camshaft sprocket from camshaft.
To install camshaft sprockets:
Place camshaft sprocket on camshaft.
Install bolt and washer to camshaft. Using Spanner Tool MB-990775, hold camshaft sprocket and torque bolt to 95 N·m (70 ft. lbs.) Camshaft Sprockets
TIMING BELT TENSIONER
Install timing belt tensioner and tensioner spring.
Hook spring upper end to water pump pin and lower end to tensioner bracket with hook out Timing Belt Tensioner
Pic in step 8
Turn timing belt tensioner counterclockwise full travel in adjustment slot and tighten bolt to temporarily hold this position Positioning Belt Tensioner

INSTALLATION
Install timing belt on crankshaft sprocket and keep belt tight on tension side Timing Belt Engine Sprocket Timing( Same pic in step 7 )Install belt on the front (radiator side) camshaft sprocket. Install belt on the water pump pulley, rear camshaft sprocket and finally on the timing belt tensioner.
Rotate the front camshaft sprocket in opposite direction to take up belt slack. Check that all timing marks are aligned Timing Belt Engine Sprocket Timing( Same pic in step 7)
Install crankshaft sprocket flange Timing Belt SystemSame pic as in step 9
Loosen tensioner bolt and allow spring to tension timing belt.
Turn crankshaft two full turns in clockwise direction. Turn smoothly and in clockwise direction ONLY.
Align the timing marks on the sprockets and tighten the timing belt tensioner locking bolt to 28 N·m (250 in. lbs.) torque.
Install timing belt covers.
Install engine support bracket.
Install right side engine mount.
Install crankshaft damper and pulleys Timing Belt System Tighten damper center bolt to 135 N·m (100 ft. lbs.)
Install accessory drive belts. Refer to COOLING SYSTEM for procedure.
Install accessory drive belt splash shield Accessory Drive Belt Splash Shield
WATER PUMP - 3.0L ENGINE
REMOVAL
Drain cooling system. Refer to procedure in this section.
Remove timing belt. Refer to ENGINE for procedure.
Remove water pump mounting bolts.
Separate pump from water inlet pipe and remove water pump Water Pump - 3.0L Engine
INSTALLATION
Clean all gasket and O-ring surfaces on pump and water pipe inlet tube.
Install new O-ring on water inlet pipe Water Pipe O-Ring Wet the O-ring (with water) to ease assembly
CAUTION: Keep the O-ring free of oil or grease.
Install new gasket on water pump and install pump inlet opening over water pipe, press assembly to cause water pipe insertion into pump housing.
Install pump to block mounting bolts and tighten to 27 N·m (20 ft. lbs.)
Install timing belt. Refer to ENGINE for procedure.
Fill cooling system. Refer to procedure in this section.

1 - BOLTS27 N·m (240 IN. LBS.)
2 - WATER PUMP
3 - GASKET
4 - O-RING
5 - WATER PIPE
Where is the water pump???
Fuel pump in tank- see dealer
there not
If you remove the right front plastic fender liner on the caravan, the water pump is lower right of the engine.
I can get to it but how does one get it out?
It is on the bottom of the washer bottle.
A Chrysler/Dodge dealer can get that part.
The pump will need replaced if it is grinding.
It is directly below centre of pump.
The water pump on a 3.0L is inside, driven by the timing belt.
it is in with the timing belt
It is the item below the ac compressor.