0
What are the standard dimensions of typical concrete masonry units aka CMU's?
Wiki User
∙ 16y ago
finished out dimensions are 8"x8"x16"
basic dimensions of a concrete block are 7-5/8"x7-5/8"x15-5/8"
Wiki User
∙ 16y ago
Add your answer:
Earn +20 pts
What is a typical value for Young's Modulus of concrete?
30-100 Gpa (in compression)
What does a typical expansion joint in a brick masonry veneer wall get filled with?
Most painters will use latex caulk. You can get silicone in a color to better match your brick but it is more expensive and harder to work with.
Why is concrete important in construction industry?
aside from the obvious factors of strength and rigidity it is also 100% reusable just add water and sand to the mix of crushed concrete and you have new cement to use also it has a typical 50 to 100 year life span
How many kg of steel reinforcement in one cubic meter concrete?
It all depends on the type and sizes of the steel used. It also depends on the load that the concrete has to take at certain points. 7865kg is the weight of a cubic meter of steel. Typical examples; A pile cap could contain 400kg/m3 A heavy duty industrial slab or structure could contain 200kg-400kg/m3 A footpath could contain 40kg/m3 (all depends on the design, but numbers above should give you a rough answer)
What is load bearing header?
A typical load bearing header will be 2 2x12s with a 7/16 plywood spacer between them.
What are the dimensions of a 10000 gallon UST?
Depending on the manufacture of the vessel, typical dimensions are 10'6" or 126" round or diameter and 15'7" long or 16 feet to be safe. Typical depth of burial is 3-4 feet down under soil and a concrete pad to keep the tank from floating up. Sometimes they are anchored down with straps and a concrete pad to counter the bouncy of the empty tank.
What are typical dimensions for apartment buildings?
what are the typical dimensions of an apartment building
What are the dimensions of a typical toilet?
The typical dimensions of a water closet (just toilet) is at least 36in. x 66in.
What is face shell thickness of hollow blocks?
Traditional Concrete Masonry Unit (CMU) Blocks have 2 rectangular voids through the block. These voids are called "Cells". The face shell thickness is the thickness of the block material from the cell to the front of the block. For example, a typical block of dimensions 8"high by 8"deep by 16" long probably has a face shell thickness of 1.25".
What are the typical dimensions of a tool shed?
8x10'
What are typical classroom dimensions?
They are 30X32 usually
What are standard desk dimensions?
29" high (to BOTTOM of desk surface) by 30" deep is very typical. Width varies greatly and should be easier for you to decide upon.
What are the measurements of an A7 envelope?
The typical dimensions for a standard A7 envelope is 5.25 inches by 7.25 inches. They can come in different colours and the packs can vary from 100 to 50 packs.
What are the typical dimensions of an over the road trailer?
48 ft
What are the standard dimensions of a 2 Pencil?
Typical Typically-sized pencil under a ruler. A standard, hexagonal, "#2 pencil" is cut to a hexagonal height of 1⁄4-inch (6 mm), but the outer diameter is slightly larger (about 9⁄32-inch (7 mm)).[
Is there a typical detail showing liner attachment to concrete?
no there is no typical detail showing liner attachment to concrete You can actually go to Youtube and find how to videos on this exact job task.
What are the dimensions of typical skyscraper advertising banner?
The skyscraper advertising banners range from as small as 10x10m and all the way up to more than 200x200m. The typical skyscraber advertising banner has the dimensions 90x90m.
