answersLogoWhite

0


Best Answer

Any time the brake pedal is hard to press then you need to check and see if the brake booster is functioning properly.

User Avatar

Wiki User

15y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: What causes hard brake pedal in VW beetle?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Continue Learning about Art & Architecture

What would cause the brake light on the dash to come on in a 1995 gmc sierra?

IS it the BRAKE LIGHT or the Parking Brake Light? If it is the BRAKE LIGHT, then your pedal must be going down far enough to hit a sensor that sets off the brake light to tell you your brakes need serviced. Normally this means you are low on brake fluid. If you are low on brake fluid FIND OUT WHY! You may have excessive brake pad wear, or a leaking brake cylinder, or your master cylinder may be going out. If you keep pumping the brakes and then stand on it hard, feel for the pedal to eventually go soft, if it does, then normally the seals in the master cylinder are going out. If you pump the brakes and the pedal never gets hard, then you have a serious brake fluid leak. If the Parkign Brake light stays on, then your parking brake is not fully releasing, at least where the contacts are to remind you it is on. This can be adjusted.


How can you tell if master cylinder is worn out?

Start the car, place you foot on the brake and push and hold it. If the brake pedal very slowly sinks toward the floor, the master cylinder is bad. Of course a leak at the master cylinder means it is bad. Don't ignore any of these 2 symptoms as it can stop working at any moment, and leave you with no brakes. When looking at the master cylinder look at the wall or booster that the master is bolted to. If u see sweating, or paint pielling at the mating the master is leaking from the seals.


What causes Brake fade?

Excessive heat, typically generated by excessive braking, incorrectly adjusted components, or improperly fitted components, or, in the case of air brake systems, faulty quick release or relay valves, brake chambers, or slack adjusters.


How do you release a parking brake with a broken release handle on a 1993 Chevrolet truck?

Best ways are if you can see exposed cable underneath the truck, go underneath and yank down on the cable as hard as you can. If the parking brake isn't needed or you just need to free the brake to move the truck and can go get it repaired if necessary, cut the cable back by the brake and the brake will release. Shouldnt cost more that 150 bucks to get a new e-brake installed.


How hard is it and How do you change master brake cylinder on 1999 Chevrolet Suburban?

The master cylinder on a 1999 suburban is pretty easy to change. Under the dash, disconnect the clutch pedal from the cylinder rod. disconnect the brake lines from the master cylinder and allow to drain into a container. Unbolt the cylinder and remove. Install the new cylinder and connect the lines and rod back up. Add new fluid, and bleed the slave cylinder to finish the installation.

Related questions

How do you change front brake pads on 2003 beetle?

put new disks and pads in my 2005 V beetle bleed them and brake pedal still not to the top go down about 2inchs how do i get a nice hard pedal


What causes your brake pedal on a 1994 pathfinder xe to get hard?

Power brake booster failure or vacuum supply to booster insufficient.


Why 1990 Geo Tracker brake pedal hard to press?

Hardness in the brake pedal can because by low brake fluid. Air in the brake lines can also cause the pedal to push hard.


What causes hard brake pedal on 1993 Geo Metro?

try bleeding the brakes or checking the fluid


How does the normal pedal feel when the abs is activated during hard brake?

The brake pedal vibrates.


Why does brake Pedal travel decreases and brake pedal get hard on ram van?

Probably the brake booster going bad.


Why is it hard to push down brake pedal?

A hard brake pedal can be caused by several different factors. It can be as simple as the brake pedal getting caught on something to the power brake booster being bad. You could also have a brake pad or shoe that is sticking, causing the brake fluid to boil. When brake fluid boils, it expands and can cause the hard brake pedal that you feel. A brake pedal that is hard to press can also be caused by a build-up of water in the brake line. The water in the brake line lowers the boiling point of the brake fluid. A hard brake pedal can also be the result of a restriction in the brake line, such as a bent brake line or foreign material in the brake fluid. The most common cause of a hard brake pedal is the sticking brake pad or shoe, causing the brake fluid to boil. Tracking down what is causing the hard brake pedal can be frustrating, to say the least. Take the vehicle for a drive and when you come back, feel your brake lines near the wheels. Caution: The line may be very hot! If one is extremely hot, you may have just found the culprit causing the hard brake pedal.


What would cause the brake pedal to be hard and still no brake lights on a 2006 Lincoln navigator?

brake switch located on the top of the brake pedal


How do you know a brake power booster is bad?

you will have a hard brake pedal


What are symptoms of a bad power brake booster?

hard brake pedal is the most obvious sign only way i know to test a booster, is to turn engine off. use brakes several times till pedal is hard. then with brake applied,start engine. the brake pedal should then soften.if the pedal stays hard the booster is bad


Why your brake pedal feel hard to press?

The power brake booster is failing.


What is wrong when 2003 Pontiac sunfire started stalled started brake pedal was hard to push when trying to back up and stalled?

why is my brake pedal hard on 2003 sunfirer