0
to the solnoide find the distributer follow the center wire to from there to the solnoide one is a positive and one is a negative wire that is where you attach to the two nuts on either side if it
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
How do you hook up a tach to a small block Chevy with HEI distributor?
On the dist., cap, where the wires go in, there is a tab labeled TACH.
Where is number 1 distributor location Chevy 350?
first port to the right of the input block where the coil and tach wires go in. looking down clockwise
How do you hook up a Sunpro tach to an MSD ignition?
There should be a tach output connection on the side of the box somewhere, you just plug your tach pickup into that. If it doesn't work you'll need a MSD tach adapter. I'm unsure of the part numbers but there are 2 different ones, it depends on what you used to wire in your ignition. If you used the white wire there is one and if you used a magnetic pickup ( green and violet wires ) there is another one....MSD-8920. I have a sunpro tach and I had to go out and buy an adapter to make it work...for about 50 bucks.
How do you install a Sunpro super tach 2 tachometer in a 1979 Chevy Silverado?
If the wires are Red,Black,Green,and White I can help you. Im also assuming you have HEI ignition. The red wire will go on the positive battery terminal, make sure you run an in line fuse. The white and black wire are for the light, so you will have to tap in to a dash light. White being positive. The green wire will go on the tach lead also known as negative. The cap has the words TACH and BAT on them. Hook it up to the TACH.
How to wire a split capacitor motor?
Your two hot wires go to the load side of your contractor and the two brown wires go to your capacitor
How many wires go to srarter on 1991 Chevy 5.7?
TWO wires
Does the live wire from the ignition key go to the bat terminal and a live wire from the starter go to the tach terminal on a hei distributor for 350 Chevy in a boat with non standard wiring?
You do need a switched live to the bat terminal, but not to the tach terminal. The tach terminal is the negative side of the coil, the bat terminal is the positive side of the coil. Normally the tach terminal is for the green wire from the tach.
How do you install a tenzo R tachometer in a 1996 Honda civic ex v-tech?
The tach has a lot of wires coming out the back, here are what the are for: ~The RED wire goes to a power source. ~The BLACK wire goes to ground. ~The BROWN and BLUE wires are for the tach internal bulbs. ~The GREEN wire needs to go to a blue wire that is located under your hood top right corner. The blue wire has a black rubber cap on it.
Where can you find tachometer pickup on 91 gmc topkick with 3116 cat engine?
All of the ones that I have worked on have the tach pickup made into the alternator, believe it or not. There are two different alternators that can go on this engine and they look the same from the outside and use all the same wires. They are delco-remy. I'll get you the part numbers.
How do you change the speed cable?
Not sure if this will help, but on most cars now, there isn't a "speed cable", there is just wires that go to the sensor on the transaxle (transmission) that goes up to the instrument cluster (speedometer, tach, gaugees, etc...).
What would cause an RPM gauge to go nutty in a 1989 Chrysler LeBaron while the car is still driving fine?
Make sure all of the wires on the coil are tight and if they are take it to a speedo shop for tach repair.
Where do the wires go on your 1992 jeep wrangler gas tank?
They go to the wire connector on the fuel tank, there are also two ground wires going from the saddle to the frame.
