0
how much viynal sising for 16x80 mobile home
Wiki User
∙ 10y ago
Add your answer:
Earn +20 pts
What is the square feet for 16x80 mobile home?
Multiply the two dimensions to get the area. The calculation will give you 1.280 square feet.
How many gutters on 16x80 mobile home?
Two gutters, an 80 ft. one on each side. Most have 3 downpipes.
How many square feet is in a 16x80 mobile home?
Multiply the two dimensions to get the area. The calculation will give you 1,280 square feet.
What is the square footage on a 16x80 mobile home?
The 16x80 measurement is the travel measurement it includes the hitch which is 4ft so really it's a 16x76 & then you would also have to exclude the exterior walls including siding, framing, and inner walls. I think when I measured my inside width it was about 14.75. so you would also need to deduct that 1.25 ft from the ends as well so then you would be @ 14.75 x 74.25 & then you could do the math so just under 1100 sq ft but still not bad.
What size generator should be used to power a 16x80 mobile home?
A 2 ton unit would be most useful for that size home. 1280SF generator will be most useful and cost less in the long run. It will also last longer because it can hold up to what is needed.
How do you obtain a title on a 16x80 mobile home that was given to you by a previous employer and the prior business abandon the home over 6 years ago and now the business no longer exists?
Mobile homes are supposed to be registered with the DMV in every state I know of. In my state, if a vehicle (an auto for example) is abandoned, one can talk to the local police dept. and/or the DMV to find out how to apply for title. I would imagine that the same holds true for mobile homes, or boats, or trailers or anything which must be DMV registered.
Your mobile home roof is 16x80 how many bundles of shingles are needed?
Roofing shingles are measured in "squares". One square is 100 square feet. *ASSUMING YOUR ROOF IS FLAT OR NEARLY FLAT* 16' x 80' = 1280 square feet. You'll need 12.8 (or 13) squares of roofing shingles. The majority of roofing shingle bundles are 3 bundles per square. 13 squares times 3 bundles per square = 39 bundles (minimum). Good luck!
How many bundles of shingles do you need to cover16x20 roof?
First you must figure out the slope of the roof.To do this: hold a Framing Square (short end) level from the rake edge of the roof with the (long end)over the edge. From 12" horizontal from the roof, measure down to the deck. This is your slope factor (# x 12).Multiply Length by width including overhangs. LIKELY 19' X 83' = 1577 sfMultiply the area by the SLOPE FACTORSLOPE FACTOR:2-12 = 1.013-12 = 1.034-12 = 1.055-12 = 1.086-12 = 1.128-12 = 1.2010-12= 1.3012-12= 1.41Add 10% to 17% for Hips Ridges and waste and starter.SO: [(16X80)XSF]X0.10= ROOF AREA (100sf roof area = 1 SQUARE)
I have a 2007 Fleetwood 16X80 mobile home that is paid for. It is located in a mobile home park.Is there anywhere I can obtain a equity loan?
First, if you have great or even just good credit you need to start with your bank. Even though not all banks do loans on mobile homes you should always start with your bank because if they do, then they will give you the best rate and the convenience of paying your payments where you bank. They will make sure you are taken care of. Second, if your bank cannot do a home equity loan on mobile home, then you have another option and that is the company that currently holds your mortgage. This could be one of many different types of lenders, but it is much easier to get lower fees and a lower rate if you try to get a home equity loan on mobile home through the company you already pay. Last, if these two options fail do not get discouraged because there is still another option. There are non conventional lenders out there that specialize in harder loans like those for mobile homes. You just have to seek one of these companies out and find out if they can help you. The good thing is they have lower standards and ca
What materials can you use for DIY manufactured home foundation panels skirting?
I bought a 1980 manufactured home last year which sits in the middle of a Kansas farm. The original vinyl skirting had been busted through by animals and blown off in several places due to constant exposure to Kansas winds and the home had a past history of considerable vermin damage due to the missing and damaged skirting. My solution was to use concrete fiberboard panels purchased at a local hardware store. I used caulk in between the panels to seal the seams. Now that winter is over, I am installing multiple foundation vents so that the underneath is properly ventilated (very important in a manufactured home). So far I have survived one winter with no frozen pipes, sustained very reasonable heating costs and no sign of vermin of any kind. The panels look great plus they have survived the cold temps and wind with no movement!!! The total cost of material was less than $500 for a 16X80 home which is far less than any other foundation panel option I researched. The panels were trenched in the ground for added stability so labor is a bit more intensive than vinyl but so far after two spring storms I am very impressed! It took me and another person two weekends to install the panels and we also built a custom hitch box cover. Email me at DBBoden@yahoo.com for more information, questions or pics of the finished project. I bought a 1980 manufactured home last year which sits in the middle of a Kansas farm. The original vinyl skirting had been busted through by animals and blown off in several places due to constant exposure to Kansas winds and the home had a past history of considerable vermin damage due to the missing and damaged skirting. My solution was to use concrete fiberboard panels purchased at a local hardware store. I used caulk in between the panels to seal the seams. Now that winter is over, I am installing multiple foundation vents so that the underneath is properly ventilated (very important in a manufactured home). So far I have survived one winter with no frozen pipes, sustained very reasonable heating costs and no sign of vermin of any kind. The panels look great plus they have survived the cold temps and wind with no movement!!! The total cost of material was less than $500 for a 16X80 home which is far less than any other foundation panel option I researched. The panels were trenched in the ground for added stability so labor is a bit more intensive than vinyl but so far after two spring storms I am very impressed! It took me and another person two weekends to install the panels and we also built a custom hitch box cover. Email me at DBBoden@yahoo.com for more information, questions or pics of the finished project.
