0
Fuses have two basic ratings. The first is current rating. The current rating is the amount of current that a fuse will safely pass before blowing. When the current flow through a fuse exceeds its rating, it opens up and breaks the circuit. If a fuse has a 5 A rating, it will open as current flow through it exceeds 5 amps. It is useful to note that there are some fuses that are designated as time delay. These fuses will sustain current in excess to their current rating for a short period before blowing. The fuse that blows immediately when its rated current is exceeded is an instantaneous fuse. The other way fuses are rated is by voltage. So when selecting a fuse, be sure that both the current and voltage rating are suitable for the application.
Fuse rating is the permissible minimal current to pass in the fuse element,without causing the fuse to blow or melt.
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
True or False The voltage rating of a fuse can be greater than the circuit voltage?
True. The voltage rating of a fuse must be greater than the circuit voltage.
What are the ratings and certificates for Columbo - 1968 Short Fuse 1-6?
Columbo - 1968 Short Fuse 1-6 is rated/received certificates of: Australia:PG (video rating) Finland:K-7 (2004) UK:U (video rating) (2004)
Why would filmmakers not submit for a rating?
Because rating of films depends on the audience not by producers. That's why rating from producers are not mention as valid.
What are fuses?
A fuse is a safety device that lies in series in a circuit between an electrical source and its associated load(s). When the current, or flow of electricity, exceeds its designed threshold, the fuse is calibrated to permanently open the series circuit, thereby disconnecting the load(s) from the power source. Unlike circuit breakers, which can be reset to allow current to flow again, once a fuse disconnects, it must be discarded and replaced with a new fuse. Fuses protect a circuit from overheating due to excessive current flow. Wires and components are designed to carry up to a certain amount of current, and if the flow of current exceeds that design limit, the wire or device could overheat. Unprotected wires and electrical devices can get so hot that they can catch fire, or heat adjacent materials to their combustion point, thus starting a fire in those adjacent materials. Modern houses are most commonly equipped with circuit breakers, not fuses, for the house wiring. Fuses are still commonly embedded in vehicles, electrical devices, and electronic components. A fuse is usually constructed using a thin metal strip or filament encased in a protective transparent glass or plastic enclosure. Each end of this metal strip is connected to a separate terminal on the outside of the fuse, and these external terminals in turn connect to matching terminals attached to the circuit being protected. All the electrical current that flows through the circuit passes through this single strip of metal inside the fuse. The metal strip inside the fuse is designed to overheat and melt if the current exceeds the fuse's rating. When this metal melts away, the strip is broken, and there is no longer a path permitting the current to flow, and therefore the fuse disconnects the electrical circuit. We commonly describe a fuse as being "blown", or we say the fuse "blows" when it disconnects the electrical circuit. Fuses are available in pre-defined ratings, such as 1 Amp, 5 Amps, 15 Amps, 25 Amps, and so on, and these ratings are clearly indicated on the fuse. Many fuses are also color coded to simplify the rating identification. The transparent enclosure permits visual inspection of the metal strip or filament, so you can see if the fuse has blown. It is important to turn off or disconnect the electrical load(s) that caused a fuse to blow, because if you leave all those electrical devices turned on, then the next fuse will also blow as soon as you replace the first one. It is also very important to replace a blown fuse with good fuse of exactly the same rating. You should never, for example, replace a 15 Amp fuse with a 25 Amp fuse, because then the wiring is no longer properly protected, and it could overheat and cause a fire. It is important to distinguish a fuse from a Ground Fault Interrupt (GFI) safety device. A fuse will not prevent death by electrocution. Nor does a fuse protect against fire due to arc faults. The fuse's only purpose is to protect against excessive current flow in a circuit. Like it's dynamite!
What rating is the 1963 Jason and the Argonauts?
It's a G Rating...:D
It is ok to use a fuse with a higher amperage rating and not ok to use a fuse with a smaller amperage rating why?
It is ok to use a fuse with a higher amperage rating and not ok to use a fuse with a smaller amperage rating why?
What is the fuse rating of 600watt appliance on a 220 volt supply?
The fuse rating should be 5 amps
What is the current rating of T2L 250v fuse?
The current rating is 2A (2 amps).
What happens if you use a fuse that's overrated for voltage but has the correct current rating?
Using a fuse correctly rated for current but "overrated" for voltage does not present a problem. Current ratings are critical safety issues, and fuses should be replaced with those of the same current rating. But using a fuse with an identical current rating but a higher voltage rating is not a problem. The reason for that lies in what the voltage rating of a fuse is. Fuses are given a voltage rating to state a maximum voltage in a circuit that they are designed to protect. And the voltage rating has nothing to do with the "normal" operation of the fuse. The fuse carries current when it operates normally, but when something happens and excessive current flows, the fusible link heats up and opens. This is where the voltage rating comes into play. It is possible that a fuse can arc through when it fails. It is the voltage rating that stands in the way of this. As long as the voltage rating of a circuit is not beyond the voltage rating of the fuse, that fuse will fail safely when it fails. It is acceptable to use a fuse of an equal current rating but a higher voltage rating when replacing a fuse that has failed.
What is meant by ratting of fuse?
A fuse is given a various rating (strength). For instance, a home appliance (washing machine, etc) would usually have a fuse with a 13 amp rating. While a low powered lamp would only merit a 2 or 5 amp fuse rating. It is important to use a fuse of the correct rating in amps for each electrical appliance.
How is the minimum fusing current related to the current rating of a fuse?
Each fuse has its own rating. It will be marked on the fuse somewhere.
What is the maximum current that can flow through a fuse?
A current rating of a fuse is designed to open a circuit at a specific current flow. This rating is imprinted on the fuse and lets you know what the maximum amount of current the fuse is designed to open at. A fuse is in the circuit to protect the conductor that the current flows through. Never over fuse a conductor's current carrying capacity.
What is the fuse rating for a kettle?
A standard 3kW immersion heater will require a fuse rating of 13 A. This is because, it draws a current of 12 A.
How fuses are rated?
Fuses are rated by amperage (current) and voltage. The larger the current need, the larger the rating of the fuse, to handle the current. The voltage rating of a fuse defines the maximum value of circuit voltage in which the fuse can be safely used. A fuse should not be used in a circuit with a voltage exceeding the voltage rating of the fuse.
Why should a fuse of defined rating not be replaced with one with larger rating?
The fuse is rated to protect the equipment, the supply, and you. Change the fuse for a higher rating and you compromise your safety and equipment and supply safety; increasing the risk of electric shock and of fire.
Why the size of a fuse holder increase as the rating of a fuse?
As a general rule, the larger the current rating of the fuse, the larger will be the fuse holder (or at least the metal contacts) because it will have to be capable of handling larger currents without overheating.
What is the amp rating of a T3.15L fuse?
3Amp
