To separate a mixture of salt and sand, take the whole thing and chuck it in a container like a bowl or bucket. Now add water to cover the mixture, and stir well to dissolve the salt. Pour the liquid off through a filter and collect the solution that comes through. Rinse the sand with more water, and let that come through the filter as well. Now you have wet sand (that has had the salt washed out of it) and a solution of salt and water. If you spread the sand out on a clean flat surface, you can let it dry and then recover your sand. Take the solution of salt and water and heat it to "reduce" it, and then put the solution on "low" to quickly evaporate the water and leave the salt. Recover the salt and finish drying it if it is not dry already. You have performed a physical process to separate a mixture, and you've recovered your two original materials.
If you are trying to save the sand, then just place everything in distilled water to dissolve the salts and then pour the mixture through a filter (coffee filter works) to collect the sand. You can rinse a few times this way to be sure it's clean. If you want to save salt, do the same thing but save the filtered water in a container (glass will be best) then evaporate the water to get the dry salt in your container.
Evaporation is recommended. Firstly, put salt and sand into water and stir well to dissolve the salt. Secondly, filter out the sand from the salt solution using a filter funnel and filter paper. Thirdly, place the beaker of salt solution on a Bunsen burner until it evaporates fully and only salt crystals are left. Lastly, heat the salt crystals and sand until it is dry.
Place the mixture in water and separate the sand from the water if you want the salt. alow the water to evaporate, and you have salt and sand separated.
by sublimation
Add water, separate the water from the sand. Let the water evaporate.
Since salt is soluble in water then you have to separate the mixture from sand first and this is done by filtration. The sand will be left in the filter paper and the filtererd solution would be that of salt and water. To get the salt you would then have to heat the solution and the water will evaporate leaving the salt behind.Filter Paper
First decant the water - the sand will be left behind. Then evaporate the water and the salt will be left behind.
filtration
You toss the sand and salt in a filter that will not allow the sand through, Then rinse the sand with clean water until all of the salt has been dissolved and removed from the sand, Then evaporate the water and you will have the salt separated from the sand.
Evaporation is recommended. Firstly, put salt and sand into water and stir well to dissolve the salt. Secondly, filter out the sand from the salt solution using a filter funnel and filter paper. Thirdly, place the beaker of salt solution on a Bunsen burner until it evaporates fully and only salt crystals are left. Lastly, heat the salt crystals and sand until it is dry.
we can separate salt and sand by solving the mixture into water salt is soluble but sand is not .
by putting all of the substances on a sheet or plate and then using a magnet underneath to pull the iron fillings away. then for your table salt and white sand you just use small mesh and voila! all wrong ... 1st, use magnet to separate the iron filling from the mixture of sand with table salt 2nd add water to dissolve the salt from the mixture with the sand and filtrate the liquid sand has separated from mixture of salt 3rd place the the filtrate liquid to a burner with a evaporating dish, the water will be evaporate and the remaining residue would be the small crystal particles which is the salt.
Table Salt.
How would you separate a mixture of table salt, sand, and talcum powder? - Quora. Throw the mixture in a sieve that'll let the talc through, but will block the salt and sand grains. Of course this only works if neither the salt nor sand are dust-sized particles. Shake the sieve over a bowl.
Salt is soluble in water, sand is not soluble; filter the solution.
Place the mixture in water and separate the sand from the water if you want the salt. alow the water to evaporate, and you have salt and sand separated.
Sulfur is S , a chemical element . Sodium chloride ( NaCl ) is the table salt , a chemical compound . Sand represents a mineral ; the composition
water