0
480V about 20A
240V about 40A
look at the nameplate
duty cycle and efficiencies vary
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
What is the star delta working principle?
when starting a 3 phase induction motor,first start with star connection,because reduced current is being applied and after start change it to delta connection then. full line current is applied to the motor.
Open Transition Switching in star delta starter?
The transition from star connection to delta connection requires that the current flow through the motor is interrupted. This is termed "Open Transition Switching" and with an induction motor operating at partial speed (or full load speed), there is a large current and torque transient produced at the point of reconnection. This transient is far worse than any produced by the DOL starter and can cause severe damage to equipment and the supply.
Discuss the special feature for selecting the fuse rating for the protection of motor?
The starting current of a motor is usually much higher than the normal current of that motor's full load condition. So for the protection purpose, in case of selecting fuse, the fuse has to be rated 2-3 times the full load of the motor so it does not blow on start. An induction motor will have a starting current of around 6 times FLC.
What is the Full load motor current of a 75KW motor?
Full load starting current is typically in the region of 5or 6 times the full load motor current;.
What happens to the rotor speed and rotor current when the mechanical load on an induction motor increase?
whenever the load increases,the current drawn by the motor to do or to fulfill the required energy to the load. so the current will increase generally.Increase in load will cause the full utilization of motor,so speed of rotor will decrease.
What is the star delta working principle?
when starting a 3 phase induction motor,first start with star connection,because reduced current is being applied and after start change it to delta connection then. full line current is applied to the motor.
What is Full load current for 40 HP star delta motor?
What is the continuous current of 10HP star delta motor
What is the ratio from no load current to full load current of an induction motor?
The ratio is between 30% to 40 %
Full form of scim and srim in three phase induction motor?
Slip Ring Induction Motor and Squirrel Cage Indution Motor
Why you make initially star-connection then delta-connection?
This type of motor starting is used to reduce the inrush current to a lower level. Once the motor is operating at the lower level of run current it changes to a delta connection which allows the motor to operate at its full load amperage rating.
Open Transition Switching in star delta starter?
The transition from star connection to delta connection requires that the current flow through the motor is interrupted. This is termed "Open Transition Switching" and with an induction motor operating at partial speed (or full load speed), there is a large current and torque transient produced at the point of reconnection. This transient is far worse than any produced by the DOL starter and can cause severe damage to equipment and the supply.
What is the formula to calculate the overload setting for a star delta starter?
Full load current ofthe motor x 0.58
What is full load current of 2HP induction motor?
Since (in North America, at least), the horsepower of a motor describes its rated output power, you need to know its efficiency in order to determine its input power, then its rated voltage, to determine its full-load current.
What is the advantage of a Star Delta Motor Starter?
The inrush current to the starting motor is lower due to the the motor coils being in series across the line creating a higher impeadence. When the starter connects to delta connection the motor is already turning and it does not have to go through the locked rotor phase. This system is being phased out now with the use of electronic soft starts and by-pass contactors.To start a motor direct on line (DOL) in delta requires approximately 6 to 8 times the full load current of the motor and delivers full torque. Delta places 415v across each of the windings on the motor. A Star-Delta starter starts the motor in Star which places 240v across each winding on the motor. This results in a lower starting current and also a lower starting torque.
How do you connect motor by star delta starting?
starter is used to limit the starting current to save the motor. for star-delta first star mode is enabled so the applied voltage is reduced to safe value after the motor catches the rated speed the mode is changed to the delta mode. hence the full supply voltage is applied to the motor.
A particular 3 phase induction motor has a LRA of 100 amps What is its approximate starting current?
LRA (locked rotor amperage) is not considered. Starting current for a motor is usually in the neighbourhood of 300% of the FLA (full load amps). The FLA is taken from the motor's nameplate.
Discuss the special feature for selecting the fuse rating for the protection of motor?
The starting current of a motor is usually much higher than the normal current of that motor's full load condition. So for the protection purpose, in case of selecting fuse, the fuse has to be rated 2-3 times the full load of the motor so it does not blow on start. An induction motor will have a starting current of around 6 times FLC.
