0
The first figure is the UTS of the bolt in hundreds of Mpa (so an 8.8 bolt fails at 800 Mpa) while the second figure is the percentage of UTS at which plastic deformation occurs, divided by 10. (so your 8.8 bolt stretches permanently at 80% of 800 Mpa, or 640 Mpa).
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
Given a sorted array- 8 13 17 26 44 56 88 97. Using binary search method find the element 88. show the contents of high low and mid at each step?
The array has eight elements indexed 0 to 7. The middle element will be found at index (0+7)/2=3. Element 3 has the value 26, which is smaller than 88, so 88 must reside in the array starting at index 4 ending at index 7. The array has four elements indexed 4 to 7. The middle element can be found at index (4+7)/2=5. Element 5 has the value 56, which is smaller than 88, so 88 must reside in the array starting at index 6 ending at index 7. The array has two elements indexed 6 to 7. The middle element can be found at index (6+7)/2=6. Element 6 has the value 88. Thus 88 was found at index 6.
What engines can be used as a replacement of the 23L Isuzu pickup motor?
The only replacement for your 2.3 is another 2.3 or a 2.6 out of a '88-91 Trooper, '89-94 Amigo, '88-95 Pup, or '91-96 Rodeo. information has been edited because the original poster has no clue what they are talking about.
What is A short tube on end of a hose called?
short tube on the end of a hose
What do you mean by quenching of steel?
quenching is rapid cooling of steel to be heat treated, there are basically four types of quenching: 1- by water. 2- by oil. 3- by air. 4- by furnace. water oil air furnace tensile stress 175*104 112*104 88*104 52*104 (N/mm2)
What time-current characteristics for a 40A type B circuit breaker?
200a for rcbos to bs en 61009-1 for bs88-2.2 and bs 88-6 400a at 0.1 sec
What is the bolt pattern on a 1960 Oldsmobile dynamic 88?
the bolt pattern on your olds is 5 on 5inch. 72 to 88 cheavy half ton truck bolt pattern. snd. Danny b.
Can you drive a oldmobile 88 with one bolt on caliper?
NO!
How do you install the AC belt on an '88 Lincoln?
1. Loosen the idler pullery bracket adjustment and pivot bolts. 2. Position a suitable belt tension gauge. 3. Install a 1/2 in. breaker bar in the hole in the idler pulley bracket. Apply tension to the belt using the breaker bar. 4. Set the tension on a new belt to 170 lbs or a used belt to 140lbs. While maintaining the tension, tighten the adjustment bolt to 30ft. lbs 5. Remove the belt tension gauge and the breaker bar. Start the engine and let it idle for 5 minutes. 6. Shut the engine off, then reinstall the belt tension gauge and breaker bar. Apply tension with the breaker bar and slowly loosen the adjustment bolt to allow belt tension to increase to the used belt specification, 140 ft. lbs. Tighten the adjustment bolt to 30 ft. lbs. 7. Tighten the pivot bolt to 50ft. lbs.
140/88 is that considered high?
140/88 is that considered high
What is the bolt pattern for 83 Oldsmobile delta 88?
my butt stinks
What engine will bolt into a 88 Montero?
2.6 Liter Mitsubishi Engine
What is the wheel bolt pattern for a 88 Chevy s-10?
Can you purchse a lug bolt seperately.I don't want the pattern I need 1 bolt lug
What is the mean for 88 85 91?
Mean = (88 + 85 + 91)/3 = 264/3 = 88
What does 88 mean in German?
88 is achtundachtzig.
What are the age of Usain Bolt's sibling's?
85 86 87 88 89
What is the bolt pattern for a 1975 delta 88 royale convertible?
The engine or the top?
What mean of 76 54 92 88 76 88 75 93 92 68 88 76 76 88 80 70 88 72?
The mean of the data is 80.
