The solution for this activity is dynamic, each one of these you download will have different IP addresses, but the Prefix (and therefore the subnet you need) are the same.
Fa0/0's is the IP with the prefix of 26, subnet is 255.255.255.192
Fa0/1's is the IP with the prefix of 24, subnet is 255.255.255.0
Fa1/0's is the IP with the prefix of 23, subnet is 255.255.254.0
There seems to also be a bug with this activity, the first one I downloaded wouldn't get past 83% complete even though my answers were correct, I redownloaded (which was how I noticed the IPs are dynamic) and put in the same answers except for the IP, and it went to 100%.
Device
Interface
IP Address
Subnet Mask
Default gateway
HQ
Fa0/0
192.168.1.129
255.255.255.192
N/A
S0/0/0
192.168.1.225
255.255.255.252
N/A
S0/0/1
192.168.1.229
255.255.255.252
N/A
B1
Fa0/0
192.168.1.1
255.255.255.128
N/A
S0/0/0
192.168.1.226
255.255.255.252
N/A
B2
Fa0/0
192.168.1.193
255.255.255.224
N/A
S0/0/1
192.168.1.230
255.255.255.252
N/A
PC1
NIC
192.168.1.126
255.255.255.128
192.168.1.1
PC2
NIC
192.168.1.190
255.255.255.192
192.168.1.129
PC3
NIC
192.168.1.222
255.255.255.224
192.168.1.193
The here is what you need to know the 192.168.23..............
Network Address Range Broadcast Mask
60 host network is 0 1-62 63 26
28 host network is 64 65-94 95 27
12 host network is 96 97-110 111 28
8 host network is 112 113-126 127 28
Point to points are easy enough for you to figure out
IP: 10.0.1.191
Subnetmask: 255.255.255.0
gateway: 10.0.1.254
This is a question regarding assessment for CCNA2. The challenge includes working on computer networks and must be done individually to get the answer.
A
Du pont
netbios is built in application in dos command mode we can use netbios in command mode. Its a default in every system that is installed with xp using netbios we can see the types of protocols used types and ip addresses of currently using servers we can also trace out ip addresses of th e servers that are connected with our servers we can also remotely work with other computers using netbios command mode some of the commands are netstat, nbtstat, tracer (posted by earningsmugglers@gmail.com)
Although it may be possible to "spike" a hacker there are programs that allow you to perform an IP Tracer which can be found at http://download.visualware.com/internetsecurity/index.htmlBut it is far better to inform athorities of the Hacking IP address inwhich the hacker will be delt with accordingly.To "spike" them and cause damage means you are no better than the hacker and can ultimatly get you in trouble or if the serge is too great you may cause harm to the user. In Australia tough new penalities being considered for computer hackers where New Federal laws are being developed to stiffen the penalties for computer hacking and other forms of cybercrime.The new bill would lift the maximum penalty for computer crime to 10 yearsjail.http://www.australianlawonline.gov.au/accesspoint?action=menuHome
42
. Completed.
Hi, Could you be more specific regarding which task in packet tracer 10.3.1 you are having trouble with completing? Regards Robert Donaghy
The password is assigned by the instructor who created the activity.
The password is: san_fran It is case-sensitive.
iskalabengbeng.. iskalaboomboompow... boombastic elephantastic.. kamuzta loba loba...
You don't. Packet Tracer doesn't support pipes.
how to unlock the config tab in packet tracer
When prompted for a password, enter one of the following: discovery1 discovery2 discovery3 discovery4 PT_user! (used for Exploration)
its a long process
class (its case sensitive)
Fixing packet tracer 9.9.1.3 can be done by running a diagnostic on that program. However if the diagnostic does not work, a simple restarting or uninstalling and reinstalling the program may be beneficial.