0
What is the correct head bolt torque specification and sequence for a 2002 Chevy S-10 truck 2.2L?
Wiki User
∙ 15y ago
The long head bolts are torqued to 46 ft lbs. + an additional 90 degrees The short head bolts are torqued to 43 ft lbs. + an additional 90 degrees * Bolt 1 Torque to: 46 ft lbs (63 Nm) * Bolt 2 Torque to: 43 ft lbs (58 Nm) * Bolt 3 Torque to: 43 ft lbs (58 Nm) * Bolt 4 Torque to: 46 ft lbs (63 Nm) * Bolt 5 Torque to: 46 ft lbs (63 Nm) * Bolt 6 Torque to: 43 ft lbs (58 Nm) * Bolt 7 Torque to: 43 ft lbs (58 Nm) * Bolt 8 Torque to: 46 ft lbs (63 Nm) * Bolt 9 Torque to: 46 ft lbs (63 Nm) * Bolt 10 Torque to: 43 ft lbs (58 Nm) Bolts 8,4,1,5, & 9 are the LONG bolts (upper row) Bolts 7,3,2,6, & 10 are the SHORT bolts (lower row) Torque in sequence from #1 through #10. The location of each bolt is 8-4-1-5-9 (upper row) and 7-3-2-6-10 (lower row). So basically you start from the middle and work your way outwards, alternating up/down.
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
What is the torque specification for spark plugs on a 2006 Chevy hhr?
specification on gapping spark plugs for 2006 chevy cobalt
Pressure plate torque specification for Chevy 350?
In 1970, the rating was 35ft/lbs.
What is the torque specification on the conecting rod cap nuts on a Chevy 305?
45 Lb/ft Below is a link to all small block Chevy torque specs.
Torque specification 305 heads Chevy?
You can find them here->http://www.boxwrench.net/specs/chevy_sb.htm
What is the spindle nut torque specification for a 2006 Chevy Equinox rear wheel?
81 ft.lbs.
Head bolt torque specs for 2003 Chevy Malibu?
I need head bolt torque specs and sequence on 2003 Chevy Malibu 3.1
What is the head bolt torque sequence for 1990 Chevy Corsica?
criss cross
What is the correct torque specification and sequence for a Chevy S-10 truck?
that depends on what you're torquing, ie wheel lug nuts, intake manifold etc. check the proper service manual for the item. intakes are in a spiral pattern from the inside bolts outward probable a step torque like (small #) ft-lbs, (higher #) ft-lbs then 180 degree turn need a special tool called a torque-angle
What are the torque specs for the head bolts on a 1986 Chevy 350?
torque, in sequence, to 35-40 ft-lbs, then repeat at 65-70 ft-lbs in sequence.
What is the torque specification on a 99 Chevy 1500 knock sensor?
There is no torque specs. on that. Just make sure it's tight and be carefull not to brake it off.
What is the correct torque specification on an edelbrock alluminum heads on a 1973 Chevy 400 small block?
Yes. For street use you may want to use the head gasket as a template to add the steam holes.
What is the torque specs for the rocker arms for a 1997 Chevy cavalier 2.2?
The torque specification for the rocker arm nut on a 1997 Chevy Cavalier is 22 foot pounds. This is the equivalent of 30 newton meters.
