0
Answer A: At Phillip's house, as it belongs to him, or with his permission.
Answer B: A Philips screwdriver has a head shaped like a plus sign, and can be used in any screws or bolts which include a plus shaped slot on the head
Wiki User
∙ 12y ago
Wiki User
∙ 11y agoThe tip of the blade is placed in the cross shaped receptacle in the head of the screw. Now, if screwing in, the wrist holding the screwdriver is rotated in a clockwise manner, thus turning the screw clockwise, at the same time as exerting pressure downwards on the screw. These combined actions will cause the tip of the screw to enter the surface of the material and penetrate inwards. Keep on turning and pressing down and the screw will seat itself in as many turns as there are threads on the screw. Threads are the spiral twists on the side of the screw, Common wood screws have about 15 -20 threads per inch. When the head (wide part) of the screw is firmly set in the material you can stop turning. Removing a screw is accomplished in exactly the opposing manner, by turning the screwdriver anti-clockwise and not putting quite so much downward pressure on, but just enough that the blade will not slip loose.
Wiki User
∙ 16y agoA Phillips screw driver is primarily used to fasten and unfasten screws with a star-like hole in their heads.
Wiki User
∙ 10y agoThe single main use is for turning Phillips head screws.
Wiki User
∙ 9y agoRather than a single slot, in which a screwdriver fits, a Philips (maker's name) screwdriver is star shaped and is less likely to slip off the screw-head and cause damage.
Wiki User
∙ 11y agoFor fitting into and turning phillips head screws.
Wiki User
∙ 11y agoThe Phillips screwdriver has a single use and that is the screwing of Phillips head screws.
Add your answer:
Earn +20 pts
Where do you use a Philips screw driver?
You use a Phillips screw driver on a Philips screw.
What kind of people that uses Philips screw driver?
that guy off one guy one srewdriver might use them
Is a screw easy to use?
Depends on what head it has, a philips (cross-head) is easier to use than a straight edge head. As long as the screw driver, or drill bit your using is the right size, they aren't bad either way you go (philips or straight) the philips are just easier to keep drivers in.
What is the name of a kind of driver used of a four slotted screw?
Philips Phillips
How do you adjust the headlights on a 2000 Kia Sportage 4 door EX model?
I would get a philips head screw driver. Then I would locate the screw on the headlight housing. I would then use the screwdriver on the screw as I needed.
What size screwdriver do you need to open the Nerf Longshot?
A Miedium size Philips screw driver
How do you remove the dash on a 93 Geo Storm?
take the screws out on the top you have to use a short Philips screw driver and theres 2 screws on the bottom then it pulls out
Where will you find the idle screw on a gilera DNA engine?
under the plastic covering in front of the rear wheel, on the carb, Philips screw driver head.
What is the use of Philips screw driver?
The cross-head (or phillips) screwdriver provides the user with more torque to turn screws - as opposed to the 'standard' slot-head version.
What is use of Philips screw driver?
The cross-head (or phillips) screwdriver provides the user with more torque to turn screws - as opposed to the 'standard' slot-head version.
How do you Change batteries in 2001 Nissan Pathfinder?
we have a 2000 and we just unscrewed it it took a large Philips screw driver
How do you change a tail light?
On most Broncos, you just unscrew the taillight lens with a Philips head screw driver and there you go.
