Want this question answered?
If it is a 30 amp breaker then it is a 240 volt outlet.
I assume you mean you are wiring a 220 volt circuit. You will install a 220 volt double pole breaker of the correct size for the circuit. An example would be for an electric dryer that requires a 30 amp double pole breaker wired with 10/3 wire. You connect the Red & Black wires to the breaker. One on each screw. You now connect the White wire to the neutral bus bar in the service panel. Then connect the bare copper ground wire to the ground bus bar in the service panel. At the dryer outlet connect the black & red to the hot screws, white to the neutral, and ground to ground. They will be labeled on the back of the outlet.
Yes, you can always have heavier wire than code requires.
If you are no longer using the dryer and there are 4-wires, and the dryer was 220 to 240 volts, it can be split into two 110 to 120 Volt circuits.
15 amp
Because a toaster does not pull near the current that a cloths dryer does.
Because a toaster does not pull near the current that a cloths dryer does.
Yes - a hair-dryer rated at 120 volts will work in a 110 volt outlet.
If it is a 30 amp breaker then it is a 240 volt outlet.
I assume you mean you are wiring a 220 volt circuit. You will install a 220 volt double pole breaker of the correct size for the circuit. An example would be for an electric dryer that requires a 30 amp double pole breaker wired with 10/3 wire. You connect the Red & Black wires to the breaker. One on each screw. You now connect the White wire to the neutral bus bar in the service panel. Then connect the bare copper ground wire to the ground bus bar in the service panel. At the dryer outlet connect the black & red to the hot screws, white to the neutral, and ground to ground. They will be labeled on the back of the outlet.
Yes, you can always have heavier wire than code requires.
If you are no longer using the dryer and there are 4-wires, and the dryer was 220 to 240 volts, it can be split into two 110 to 120 Volt circuits.
Theoretically yes if you remove the two pole 50 amp breaker and replace it with a 2 pole 15 amp breaker. This has to be done because the new receptacle is only rated at 15 amps and can not be protected by a breaker any larger than 15 amps.Physically this is not going to happen due to the fact that you will not be able to connect the existing #6 conductor, which fed the 50 amp dryer receptacle, under the terminals of the new 2 pole 15 amp breaker.
There is no requirement on the distance the dryer must be from a sink. Any 120 volt outlet must be GFCI protected if it is within 6 feet of a sink. There is no requirement for a 240 volt dryer outlet. I would not want the dryer right next to the sink and I would want the dryer to be on a 4 wire circuit and not a 3 wire circuit. Use common sense here.
for USA, Canada and other countries running a 60 Hz supply service.No - unless it is a very low power model, in which case it would already have a standard 120 volt plug on its flexible power cord - a normal clothes dryer cannot be plugged into a regular outlet. You need to use the right size 240 volt outlet that is connected to the right size cable and circuit breaker in your main breaker panel.As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energized.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
On a 240 volt outlet, such as a dryer outlet: G is Ground, W is Neutral, X and Y are the two Hot legs.
15 amp