0
Breakers are sized by the conductors that are connected to them. Conductors are sized by the amperage that the load draws.
The electrical code states that a 50 HP 460 volt three phase motor draws 65 amps. The ideal amperage would be taken from the motors nameplate as different motors of the same horsepower will have different amperage's depending on what they are designed to do.
The feeders for this motor have to be sized at 125% of the motors full load amperage. 65 x 125% = 81 amps. A #4 copper conductor with and insulation rating of 75 or 90 degrees C is rated at 85 amps.
The breaker for this motor is 150 amp or 175 amp fusing or 110 amp time delay fusing.
Wiki User
∙ 11y ago
Wiki User
∙ 13y agoUse MCCB which is 450Amps. Generally we can load up 80% for long life
Add your answer:
Earn +20 pts
Fuse size for 7.5 HP 3 Phase 440 Volt Motor?
The electrical code states that a 7.5 HP 460 volt three phase motor draws 11 amps. For fuse sizes, non time delay - 30 amps, time delay type D - 20 amps and if using a breaker it will be 30 amps. Minimum wire size is #12 and the maximum setting of overload devices will be 13.75 amps
Will a 208 volt 3 phase generator supply operate a 230 volt 3 phase motor?
Yes, but the motor's horsepower rating will not be reached.
How can I connect a single-phase - 2 hot wires plus ground- 220V load to a 3-pole 220V breaker?
Common usage of a three pole breaker is for use on a three phase distribution panel. Single phase distribution panels only use two pole breakers for a 240 volt load.Remember that the breaker must protect the conductors that connect to the load. If you want to try and use a three pole breaker in a single phase panel just because you have the breaker, this is not a good idea even if it will fit.Purchase the proper single phase two pole breaker to match the wire size and the amperage of the connected 240 volt load. Keep in mind that connected 240 volt motor loads have to be sized to 250% of the motor's full load amperage.By doing what you want to do and a fault occurs from this type of installation your insurance company might not cover the damage that it would cause.If the distribution panel is three phase then just connect the two load wires to any two of the three poles on the breaker.
How do you change a 3 phase 440 volt motor to a 3 phase 220 volt motor?
You can not change it. 440 volt is by design. However you run it with 220 single phase supply, but it would run far lower power.
How do you get a 380 volt 3 phase motor to run on a 220 volt 3 phase power source?
Use a transformer.
What size breaker for a 208 volt single phase motor that pulls 1.4 amps?
208 volts is not a common single phase voltage but you could just size your breaker to the capabilities of the conductor. 208 is normally a phase to phase voltage <<>> Many 230 volt motors can be connected to lower voltage supplies. These motors can be connected to supplies of 208 and 200 volts. The code requirement is that the 230 volt full load amperage of the motor be increased by 10% and 15% respectively for wire sizing and breaker selection. To answer the question you will need a two pole 15 amp breaker.
Can you run 22 kw 600v 3 phase induction motor?
Yes this size motor can be operated by bringing a 600 volt three phase supply to it.
Fuse size for 7.5 HP 3 Phase 440 Volt Motor?
The electrical code states that a 7.5 HP 460 volt three phase motor draws 11 amps. For fuse sizes, non time delay - 30 amps, time delay type D - 20 amps and if using a breaker it will be 30 amps. Minimum wire size is #12 and the maximum setting of overload devices will be 13.75 amps
Will a 208 volt 3 phase generator supply operate a 230 volt 3 phase motor?
Yes, but the motor's horsepower rating will not be reached.
How can I connect a single-phase - 2 hot wires plus ground- 220V load to a 3-pole 220V breaker?
Common usage of a three pole breaker is for use on a three phase distribution panel. Single phase distribution panels only use two pole breakers for a 240 volt load.Remember that the breaker must protect the conductors that connect to the load. If you want to try and use a three pole breaker in a single phase panel just because you have the breaker, this is not a good idea even if it will fit.Purchase the proper single phase two pole breaker to match the wire size and the amperage of the connected 240 volt load. Keep in mind that connected 240 volt motor loads have to be sized to 250% of the motor's full load amperage.By doing what you want to do and a fault occurs from this type of installation your insurance company might not cover the damage that it would cause.If the distribution panel is three phase then just connect the two load wires to any two of the three poles on the breaker.
What size wire and breaker for a 240 volt single phase 20 kw electric furnace rated at 83.3 amps?
AWG #3 copper.
How do you change a 3 phase 440 volt motor to a 3 phase 220 volt motor?
You can not change it. 440 volt is by design. However you run it with 220 single phase supply, but it would run far lower power.
Can you run a 570 volt motor on 480 volt three phase power supply?
No, the voltage difference is too much. A 570 volt motor falls in the 600 volt range which is separate from the 480 volt range of three phase systems.
How do you get a 380 volt 3 phase motor to run on a 220 volt 3 phase power source?
Use a transformer.
What size time delay fuse do you use on a 40 hp 230 volt 3 phase motor?
The electrical code book states that a 40 HP 230 volt three phase motor draws 104 amps. For that motor the wire must be rated for 131 amps, Non time delay fuses at 300 amps, time delay fuses at 175 amps or a 250 amp circuit breaker. When calculating wire sizes and motor protection the motor's full load amperage should be taken from the motor's nameplate.
On a 220 volt electric motor which is the neutral wire L1 L2 or L3?
If the motor wire numbers are L1, L2 and L3, it is not a single phase motor. It is a three phase motor. Also for future reference, a 220 volt single phase motor does not use a neutral.
What happens when you connect a 110 volt motor to 220 volts?
On a three wire supply system if you connect the two 110V wires together and they are across the phase they will short out and trip the breaker. If the two 110V wires are supplied from across the phase and connected to a motor then the motor will run. If the 110V wires are on the same phase nothing will happen.
